Skip to main content
Fire ProtectionReviewed against current OSHA standards

Where Are the Extinguishers on Your Job Site? What OSHA 1926.150 Requires of a Construction Fire Protection Program

29 CFR 1926.150 requires a fire protection program on every construction job. See what it says about extinguisher count, distance, alarms, and water supply.

Updated October 26, 2026
8 min read
By the WorkSafely safety team

Picture a small remodeling crew on the second day of a tenant build-out. The drywall is up, a pallet of flooring is stacked in the hallway, a painter is opening cans of solvent-based primer, and the electrician has just left a work light burning against a pile of cardboard. Somewhere in the truck there is an extinguisher, but nobody has been asked where it is, and nobody has decided who calls the fire department if the cardboard catches. The building has no working sprinklers yet, and the crew has no plan for what happens in the first two minutes of a fire.

That gap is what 29 CFR 1926.150, titled "Fire protection," is written to close. It sits in Subpart F of the construction standards, and it works differently from the general industry rule for extinguishers. If you have read our piece on portable fire extinguishers under 1910.157, set that frame aside for a moment. A construction site changes every week, has no permanent fixtures, and often has no building systems at all. The construction rule is built around that reality, and it puts the burden on the employer to create the protection rather than inherit it from a finished building.

This post answers one question: what does 1926.150 actually require a small contractor to have in place on a job, and what does that look like in practice? It does not cover hot work permits, flammable liquid storage rules, or the full fire prevention requirements of the neighboring sections. Those are separate questions, and we link to them below.

The standard starts with a program, not a product

Many contractors read 1926.150 and go straight to the extinguisher numbers. The paragraph that comes first is more important. Under 1926.150(a), the employer is responsible for developing a fire protection program that is followed throughout all phases of the construction and demolition work, and for providing the firefighting equipment the subpart specifies.

Two details in that paragraph are easy to miss. First, firefighting equipment must be accessible at all times. An extinguisher that is mounted correctly but sits behind stacked drywall, or locked inside a trailer, does not meet that expectation. Second, equipment must be kept in working order and replaced promptly when it is defective. A discharged or damaged extinguisher is not protection; it is a prop.

The paragraph also contemplates a trained and equipped fire brigade where the work warrants it. For most small contractors a brigade is not realistic, and nothing here suggests a two-person crew needs one. The point for a small firm is that "program" should mean something you could explain on the spot: who is responsible for the equipment on this job, where it is kept, how it is checked, and how the crew raises the alarm. A written paragraph in your site safety plan that answers those four questions is a better program than a vague assumption that someone will deal with it.

Portable extinguishers: the rating, the area, and the walking distance

The core of the standard for most small jobs is 1926.150(c). Where you are working in or around a building, the rule asks for a fire extinguisher rated not less than 2A for each 3,000 square feet of the protected building area, or major fraction of that area. It also says the travel distance from any point of the protected area to the nearest extinguisher may not exceed 100 feet.

Those two requirements work together, and the second often bites first. A single-story building of modest size may technically need only one extinguisher by square footage, but if the far corner is more than 100 feet from where that extinguisher hangs, one is not enough. Walk the job the way a person would run during a fire, and place extinguishers so that no point in the work area is more than that distance away.

There are a few related placement rules worth knowing. The standard calls for at least one extinguisher on each floor, and in a multistory building, at least one placed adjacent to a stairway. That makes sense: stairs are the way out and also the way in for responders, so an extinguisher there is available both for the crew and for anyone trying to keep the exit usable.

The standard also deals with specific hazards. Where more than 5 gallons of flammable or combustible liquids, or more than 5 pounds of flammable gas, are being used on the job, it requires a fire extinguisher rated not less than 10B within 50 feet of that activity. That is the painter with the primer, the crew thinning coatings, or the plumber with a propane torch kit. The 2A extinguisher you placed for general combustibles such as wood, paper, and cloth is not what the rule asks for here. Check the label on what you own, because the rating is printed on it.

The rule allows certain substitutes in place of a 2A extinguisher under specified conditions, such as a water drum with fire pails or a hose line of a particular size. Those are more relevant to larger sites with water available. For a small crew, a properly rated extinguisher is the simpler path, and it is the one this post assumes.

Extinguishers must be listed, inspected, and protected from freezing

Three more points in the same paragraph deserve attention because they are where small contractors most often fall short.

The first is that only extinguishers listed or approved by a nationally recognized testing laboratory may be used. A bargain unit from an unknown source, with no listing mark, does not satisfy the rule. The second is that extinguishers must be periodically inspected and maintained in accordance with the NFPA standard the regulation references. In practice that means someone looks at each unit on a regular schedule, confirms it is charged, unobstructed, and undamaged, and keeps a record that this happened. A tag with initials and dates, hung on the unit, is a common way to do this.

The third is freeze protection. Extinguishers and water drums that are subject to freezing must be protected. A crew working outdoors through a cold spell cannot leave a water-based unit on an open deck overnight and assume it will work in the morning. Check what type you have and what its manufacturer says about temperature.

The standard also bans carbon tetrachloride and other toxic vaporizing liquid extinguishers. You are unlikely to buy one new, but an old unit inherited with a used truck or a bought-out business can still turn up in a toolbox, so it is worth a look.

Water, sprinklers, and standpipes in buildings under construction

Some small contractors work on larger projects as subcontractors, where the general contractor controls water supply and fixed fire protection. It is still worth understanding what the standard says, because it affects what you can count on.

Under 1926.150(b), a water supply of adequate volume, duration, and pressure to operate the firefighting equipment must be made available as soon as combustible materials accumulate on the site. If underground water mains are being provided, they are to be installed, completed, and made available for use as soon as practicable.

Paragraph (d) covers fixed equipment. Where sprinkler systems are being installed, installation is to follow construction closely and the system is to be placed in service as soon as legally permitted after each story is completed. During demolition or alterations, existing sprinkler systems are to be kept in service as long as reasonable, and control valves may be operated only by authorized persons and must be checked daily at the close of work. Standpipes must be operational as construction progresses, with fire department connections and at least one hose outlet on each floor.

If you are the sub working inside a building where these systems are supposed to be live, ask the general contractor directly. Is the sprinkler system in service on this floor? Has a valve been closed for other work? If the answer is unclear, you need extinguishers sized to the assumption that fixed protection is not available. Do not assume the building will protect you because it will eventually have sprinklers.

An alarm that actually reaches someone

The last paragraph of the standard, 1926.150(e), is the shortest and the most overlooked. The employer must establish an alarm system, such as a telephone system or a siren, to alert employees on the site and the local fire department. The alarm code and reporting instructions must be posted at the phones and at the employee entrances.

For a small crew, the practical version is plain. Decide how a fire will be announced to everyone on the job, especially in a building where people may be on different floors with power tools running. Decide who phones the fire department and what address they give, since a new construction site may not have a street number that dispatch recognizes. Then post those instructions where people will see them when they walk in. Our guide to employee alarm systems under 1910.165 covers the general industry equivalent and may help you think through audibility and communication.

A walkthrough you can do on Monday morning

Following this post does not by itself make a job compliant, and 1926.150 is one part of a wider set of fire requirements for construction. But a short walkthrough will tell you quickly whether the basics are in place. Start at the entrance and look for the alarm instructions. Walk each floor and count extinguishers. From the farthest corner of each work area, estimate the distance back to the nearest one. Read the rating on each label and compare it with what is being used nearby, especially solvents, fuel, and gas. Look for a dated inspection tag. Check that nothing is stacked in front of any unit, and that the crew knows where they are without being told.

If the answers vary from one job to the next, that is the sign that your fire protection program exists in your head rather than in your process. Writing it down, even in a paragraph on your site checklist, is the first step toward making it repeatable.

Related reading: Portable fire extinguishers under 1910.157 | Hot work permits for small business | Flammable and combustible liquids storage under 1910.106

OSHA standards cited

Always verify current OSHA standards at osha.gov. This article reflects standards in effect at the date of publication.

Not sure where you stand?

Take the 5-minute compliance assessment. Answer a few questions about your business and get a prioritized list of what OSHA expects, free.

Start free assessment