Skip to main content
PPEReviewed against current OSHA standards

Safety Boots for a Small Crew: What OSHA 1910.136 Actually Asks Of You

OSHA 1910.136 sets when employees need protective footwear and what it must meet. A plain guide for small shops, with notes on who pays under 1910.132(h).

Updated October 16, 2026
8 min read
By the WorkSafely safety team

A new hire starts on Monday in your shop and shows up in running shoes. You hand him a pallet jack and a list of jobs, and somewhere around Wednesday a drum of parts rolls off a cart and lands across his foot. Nobody was careless in any dramatic way. The question nobody asked on Monday was whether the work in that area called for protective footwear, and if so, whose job it was to say so.

That is the situation OSHA's foot protection standard, 29 CFR 1910.136, is written for. It is a short rule, and small employers tend to either ignore it or over-read it into "everyone wears steel toes everywhere." Neither is what the text says.

What 1910.136 requires, in plain terms

The core duty is in paragraph (a). The employer must ensure that each affected employee uses protective footwear when working in areas where there is a danger of foot injuries from falling or rolling objects, from objects piercing the sole, or when the employee's feet are exposed to electrical hazards. The rule is triggered by the hazard in the area, not by a job title or an industry label.

Notice what that language leaves out. It does not say every employee in a warehouse, or every employee in a machine shop. It says affected employees working where those specific dangers exist. A front-office bookkeeper who never crosses the shop floor is not affected. The same bookkeeper walking through the receiving dock during a heavy delivery might be, depending on how that area actually runs.

Paragraph (b) addresses quality. Protective footwear has to comply with one of the consensus standards the rule lists, which are the ASTM F2412 and F2413 pair for testing and performance, or the older ANSI Z41 editions the rule names. In practice this means you look for the marking inside the boot or on its tongue label rather than trusting the word "safety" on a box. A boot that looks sturdy but carries no marking has told you nothing about whether it will protect a toe from a falling load. The label also tells you which protections the boot has, such as impact and compression resistance for the toe, puncture resistance for the sole, or an electrical hazard rating.

Construction work falls under a sibling rule, 1926.96, which carries its own footwear requirement for construction employees. If your crew does both shop and field work, read both so you do not assume one rule's wording covers the other's setting.

Start with the hazard, because the hazard decides the boot

The footwear standard works together with the general PPE standard, 1910.132. Under 1910.132(d), the employer must assess the workplace to determine whether hazards are present that require PPE, select the right equipment for those hazards, and put the assessment in writing with a certification that identifies the workplace evaluated, the person certifying, and the date. Foot hazards belong in that walk-through just as much as eye, hand, and head hazards.

A useful way to run it is area by area rather than job by job. Walk the receiving dock, the storage racks, the fabrication area, the maintenance bay, and the yard. In each, ask three plain questions. Can something heavy fall or roll onto a foot here? Can a nail, a wire end, a metal shaving, or a sharp offcut come through a sole? Are there energized parts or wet floors where electrical contact through the feet is a realistic path?

If the answer to the first is yes, you are looking for a toe rated for impact and compression. If the second, you need puncture-resistant soles. If the third, an electrical hazard rated boot is the starting point, with an important caveat: that rating is meant as a secondary source of protection against accidental contact with live circuits under dry conditions. It does not make a worker safe to work on energized equipment, and it does not replace lockout/tagout or the electrical safe work practices that actually control that hazard.

Write down what you found, area by area, in plain language. "Receiving dock: pallets and drums handled by hand and pallet jack, risk of crush injury to the toes; safety-toe footwear required." That sentence is a useful assessment entry. "Footwear: yes" is not, because six months later nobody, including you, will remember why.

The grey zones where small shops get stuck

Several questions come up again and again, and the standard answers them only partly, so it helps to be clear about what is settled and what is your judgment call.

First, ordinary work shoes. A comfortable leather shoe with no toe cap and a thin sole does not meet the standard in an area with a crush or puncture hazard. If your assessment says an area needs protective footwear, a dress shoe or a running shoe is not a workaround, however well it is liked.

Second, metatarsal guards. The standard does not spell out when a boot needs extra coverage over the top of the foot. That falls out of your hazard assessment. If workers handle heavy items that can land on the instep, such as castings, steel stock, or drums, and the assessment says the toe cap alone leaves a gap, you decide on the right protection and document why.

Third, slip resistance. People often assume safety boots solve slipping. Footwear standards have their own provisions on outsoles, but 1910.136 is about falling objects, piercing, and electrical hazards. If your floors are wet or oily, your answer starts with housekeeping and the walking-working surfaces rules, with outsole choice as a supporting measure.

Fourth, visitors and delivery drivers. Your duty runs to your own affected employees, but a driver who walks into an active shop area is exposed to the same overhead and rolling hazards. Many small employers set a simple site rule that anyone entering a marked area follows the same footwear requirement, and keep a few loaner options or limit visitors to a safe path. That is a policy choice, not a line in 1910.136, and it reads better when it is stated in advance than when argued at the door.

Who pays for the boots

This is where the footwear rule meets the money, and it is the question employees ask first. The payment rule is in 1910.132(h), not in 1910.136. In general, the employer must pay for required PPE. There is a specific carve-out for non-specialty safety-toe footwear, such as ordinary steel-toe or composite-toe work boots: the employer is not required to pay for them, provided the employer permits the employee to wear them off the job site. Specialty items that are not suited to wear outside work, like metatarsal-guarded boots for a foundry or rubber boots needed only for a specific wet process, are not covered by that carve-out, and the employer would pay for those.

Many small employers choose to pay or reimburse part of the cost anyway, either through a boot allowance or by running a small purchase program, because it improves compliance and avoids arguments about whose job it is to buy the boots. If you do, write the policy down, including whether replacements for worn-out boots are covered and how often. Our guide on who pays for PPE under 1910.132(h) walks through the full set of exceptions and how they interact with state rules, which can differ from the federal baseline.

Putting it into a routine a small crew will follow

A footwear rule that exists only in a binder does nothing. Four habits make it real.

Say it at hiring. The first conversation, not the first week, should include which areas require protective footwear, what the markings mean, and what the company will or will not reimburse. This is also the natural moment to cover the training duties under 1910.132(f), which ask the employer to train each employee who must use PPE on when it is necessary, what kind is necessary, how to put it on and care for it, and its limitations.

Look at the boots, not just whether people have them. Footwear wears out. A split upper, an exposed steel cap, a sole separating from the welt, or a puncture that has been "temporarily" taped over are all signs the boot is no longer doing its job. 1910.132(e) says that defective or damaged PPE shall not be used, and that applies to a boot with its toe cap showing through just as it does to a cracked face shield. A quick look at the start of the shift by the supervisor, plus an easy path to replace worn boots, handles most of this.

Match the rule to what you actually enforce. If the policy says boots are required in the fabrication area and everyone knows the lead hand wears sneakers there, the written rule has become decoration, and in an inspection or after an injury it is the unenforced rule that gets noticed. Either enforce it consistently or change the rule to match a real, defensible assessment.

Re-assess when the work changes. A new rack system, heavier stock, a new conveyor, or a move to a bigger building can change where the foot hazards are. Treat footwear as part of the same review you do when you change processes.

If it helps to have a structure for the assessment itself, our PPE hazard assessment checklist walks through the workplace area by area and gives you the written certification 1910.132(d)(2) asks for, with foot protection as one of the hazards to consider.

The takeaway for the owner

Foot protection under 1910.136 is a hazard-driven rule. Find out where something heavy can land on a foot, where something sharp can come through a sole, and where electrical exposure is realistic. Decide, in writing, which areas need protective footwear and which markings you will accept. Make the rule clear on day one, settle who pays before anyone asks, and check that the boots people wear are still in working condition. None of that requires a safety department. It requires one walkthrough, one page of notes, and a supervisor who actually looks down.

This article is general information, not legal advice. Check the current text of the standards and any state rules that apply to your workplace.

Related reading: Hard Hats and Safety Shoes: What OSHA's Head and Foot Protection Standards Actually Require | PPE Training Under 1910.132(f): What You Must Teach, Demonstrate, and Write Down | Who Pays for PPE? What OSHA's 1910.132(h) Actually Requires Small Employers to Cover | Cold Stress & PPE: When Safety Gear Fights Back

OSHA standards cited

Always verify current OSHA standards at osha.gov. This article reflects standards in effect at the date of publication.

Not sure where you stand?

Take the 5-minute compliance assessment. Answer a few questions about your business and get a prioritized list of what OSHA expects, free.

Start free assessment