The Seasonal Hire Says He's Forklift Certified: What OSHA 1910.178(l)(5) Lets You Skip, and What It Doesn't
A new hire's old forklift card doesn't transfer. What OSHA 1910.178(l)(5) lets you skip in training, and the evaluation and certification you still owe.
The orders have doubled since Halloween, the staffing agency sent you three people on Monday, and one of them walks in holding a wallet card from the distribution center he worked at last year. It says he completed forklift operator training. He tells you he has driven a sit-down counterbalance truck for four years. You are short a driver on the afternoon shift, the trailer is backed into door two, and the obvious move is to hand him the keys.
This post answers one narrow question: when a new or seasonal employee arrives already trained on forklifts, how much of the training under 29 CFR 1910.178(l) can you skip, and what do you still have to do yourself before that person drives on your floor? It is a different question from what happens to operators you already employ as time passes, which is covered in our post on forklift retraining triggers. It is also not about the daily pre-shift truck inspection, which is its own requirement.
The card belongs to the last employer
The forklift standard puts the training obligation on the employer, not on the operator. 1910.178(l)(1)(i) says the employer shall ensure each powered industrial truck operator is competent to operate a truck safely, as demonstrated by successfully completing the training and evaluation the paragraph describes. 1910.178(l)(1)(ii) adds that before you permit an employee to operate a truck, other than for training purposes, you have to ensure that operator has completed that training, except as the duplicative-training provision allows.
That is why there is no such thing as a portable OSHA forklift license. The wallet card is evidence that another employer, at some point, trained and evaluated this person on their trucks in their building. It can be useful evidence. It is not your certification, and it does not tell you whether he can handle your truck, your aisles, your dock plates or your mix of foot traffic.
The standard's structure explains why. Training under 1910.178(l)(2)(ii) is a combination of formal instruction, practical training and an evaluation of the operator's performance in the workplace. Under 1910.178(l)(3), the content splits into truck-related topics, such as controls, steering, visibility, capacity and stability, and workplace-related topics: surface conditions, the composition and stability of loads, load manipulation and stacking, pedestrian traffic, narrow aisles, ramps and sloped surfaces, hazardous locations, closed or poorly ventilated areas, and other conditions unique to the workplace. Half of that list is about where the truck is driven. No previous employer could have covered your building.
What 1910.178(l)(5) actually lets you skip
The relief is in 1910.178(l)(5), titled avoidance of duplicative training. Read closely, it is narrower than the way people quote it. If an operator has previously received training in a topic listed in (l)(3), and that training is appropriate to the truck and working conditions the operator will encounter, additional training in that topic is not required, provided the operator has been evaluated and found competent to operate the truck safely.
Three conditions sit inside that sentence. The relief works topic by topic, not for the whole program. The prior training has to fit your truck and your conditions, not just forklifts in general. And the evaluation is not optional. The paragraph lets you skip repeating instruction; it never lets you skip finding out whether the person can actually drive safely where you will put them.
OSHA addressed this directly in a 1999 letter of interpretation written to a warehouse trade association that was asking about new and temporary operators who claimed prior training. The agency's answer was that the employer would be required to evaluate the applicability and adequacy of the prior training. The letter points at the things you would expect to matter: the type of equipment the person was trained on, how much experience they have with it, how recent that experience is, and the kind of environment it was gained in. It also notes that the employer may, but is not required to, use written documentation of the earlier training. In other words, the wallet card helps you decide what to cover, but you can evaluate competence directly whether or not the card exists. The letter expects that some site-specific training will almost always be needed.
So for the man at door two, four years on a sit-down counterbalance truck could reasonably let you skip most of the truck-related instruction for the same type of truck, once he has shown you he can operate it. It does nothing for the workplace topics. Your dock, your racking heights, your pedestrian walkways and the spot by the battery charger where the floor is always wet are new to him.
Watching him drive is the part you cannot skip
The evaluation under (l)(2)(ii) is an evaluation of performance in the workplace. That means someone watches the operator drive the truck he will actually use, doing the work he will actually do, in your building. A conversation in the office about what he did at his last job is not that.
1910.178(l)(2)(iii) says training and evaluation have to be conducted by persons who have the knowledge, training and experience to train powered industrial truck operators and evaluate their competence. In a small operation that is often the owner, a lead hand or the most experienced driver, and that is fine if the person genuinely knows the truck and knows what safe operation looks like. It is worth being honest about whether that is true before you assign the role.
A useful evaluation is specific. Have him pick and set down a load at the highest rack position he will use, travel the main aisle where people walk, cross onto the trailer over the dock plate, back out with a load that blocks forward visibility, park, and shut the truck down properly. Notice whether he looks behind before reversing, whether the forks are lowered when he leaves the truck, how he takes the ramp, and whether he slows at blind corners without being told. If anything you see is wrong, that tells you which topics are not duplicative after all.
Until the evaluation is done, 1910.178(l)(2)(i) still lets him operate a truck as a trainee, but only under the direct supervision of someone with the knowledge, training and experience to train operators and evaluate their competence, and only where the operation does not endanger him or other employees. Putting him alone on the afternoon shift because the card looked convincing is the situation the standard is written to prevent.
Different truck, different building, different topics
The most common way prior training stops being "appropriate to the truck" is a change of truck type. An operator with years on a sit-down counterbalance truck may never have driven a stand-up reach truck, an order picker, or an electric pallet jack you ride on. Those are different machines with different controls and stability characteristics. The 1910.178(l)(4)(ii) refresher triggers make the same point for your existing staff, listing assignment to a different type of truck as a reason for refresher training and evaluation. For a new hire, it simply means the truck-related topics for the unfamiliar truck are not duplicative.
The same logic applies to fuel types and attachments. If he was trained on electric trucks and yours run on propane, cylinder changing is a topic he has not covered. A clamp or side-shift attachment changes how loads behave. Rough or icy yard surfaces in December, or a cold-storage area where he will be in and out of a freezer, are workplace conditions the last job may not have had.
Seasonal and temporary workers add one more layer. When the person comes through a staffing agency, you as the host still control the truck, the floor and the supervision. The 1999 letter notes that a host employer supervising temporary operators is responsible for their safe operation. Agree in writing with the agency who does what, but do not assume the agency's training covers your site, because it cannot. Our temp worker onboarding checklist walks through the host-employer side of that split, including the site-specific hazards to cover on day one.
The certification is yours to sign
Once he has been evaluated and given whatever training the evaluation shows he needs, 1910.178(l)(6) requires you to certify that he has been trained and evaluated. The certification has to include the operator's name, the date of the training, the date of the evaluation, and the identity of the person or people who performed the training or evaluation.
For an experienced hire, it is worth writing down why you skipped what you skipped. A short note that says which truck types he was evaluated on, which truck-related topics were accepted from prior training and why, and which workplace topics you covered on site will make far more sense to an inspector than a photocopy of another company's card stapled to a blank form. Keep the copy of his old card if you have it, as supporting evidence, not as the certification.
Two more things follow from that record. The three-year clock in 1910.178(l)(4)(iii) for evaluating each operator's performance runs from your evaluation, so put it in your calendar. And if he is only with you for the peak season and comes back next autumn, his evaluation from this year is a starting point, not an automatic pass, if the trucks, the layout or his recent experience have changed in between.
None of this makes your forklift program compliant on its own, and it is not legal advice. It does give you an honest answer to the question you will be asked at door two this afternoon: yes, you can use what he already knows, but you have to see him drive first, and the signature on the certification has to be yours.
Related reading: Your Forklift Operators Were Certified Once | Pedestrian-Forklift Separation | The Forklift Pre-Shift Inspection OSHA Actually Requires
OSHA standards cited
- 29 CFR 1910.178
General Industry Standards
Always verify current OSHA standards at osha.gov. This article reflects standards in effect at the date of publication.
Not sure where you stand?
Take the 5-minute compliance assessment. Answer a few questions about your business and get a prioritized list of what OSHA expects, free.
Related Articles
Continue learning about OSHA compliance and workplace safety
Warehousing
The Mezzanine Is Full of Holiday Overflow: What OSHA 1910.22(b) Means by 'Maximum Intended Load'
29 CFR 1910.22(b) says every walking-working surface must hold its maximum intended load. What that means for a small shop's mezzanine in the holiday rush.
Warehousing
Dockboards and Bridge Plates: What OSHA 1910.26 Requires
OSHA 1910.26 governs dockboards and bridge plates at loading docks. Learn the rated-capacity, edge-protection, and securing rules small warehouses miss.
Warehousing
Pallet Racking and Storage Safety: What OSHA Expects Under 29 CFR 1910.176
A practical guide to OSHA 1910.176 storage and housekeeping rules for small business warehouses, covering racking load limits, aisle clearance, and stacking hazards.