Skip to main content
WarehousingReviewed against current OSHA standards

The Mezzanine Is Full of Holiday Overflow: What OSHA 1910.22(b) Means by 'Maximum Intended Load'

29 CFR 1910.22(b) says every walking-working surface must hold its maximum intended load. What that means for a small shop's mezzanine in the holiday rush.

Updated November 21, 2026
8 min read
By the WorkSafely safety team

Every November the same thing happens in a lot of small warehouses, retail backrooms and shops. The floor fills up with holiday stock, the receiving area disappears under pallets, and somebody says the obvious thing: put the overflow upstairs. The mezzanine that normally holds a few boxes of seasonal décor and some spare parts suddenly carries cases of product stacked waist high, a pallet jack that was never meant to go up there, and two people picking orders from it all afternoon.

This post answers one narrow question: what OSHA actually requires about how much weight that mezzanine, platform or storage loft can carry, and how a small business with no engineer on staff can make an honest decision about it. The neighbouring questions, the guardrails and toeboards around the edge and the racking downstairs, have their own posts, linked at the end.

What 1910.22(b) says, and what it leaves out

The rule is one sentence. Under 29 CFR 1910.22(b), "the employer must ensure that each walking-working surface can support the maximum intended load for that surface." A walking-working surface, in OSHA's general industry definitions, is any horizontal or vertical surface on or through which an employee walks, works or gains access to a work area. A mezzanine, a storage loft over an office, a platform above a production line and the deck of a raised work area all qualify the moment someone goes up there to put something down or pick something up.

Notice what the sentence does not say. It does not give you a number. It does not say a mezzanine must be rated for a particular load per square foot, and it does not tell you how to calculate anything. It puts the obligation on you, the employer, to know what the surface is going to be asked to hold and to be sure it can hold it.

That is a change from the older version of the rule. Before OSHA's walking-working surfaces final rule was published on November 18, 2016, general industry had a specification-style requirement that employers post approved load ratings in buildings. OSHA's own FAQ on the final rule explains that the posting requirement was dropped because load information is available in building plans, and the rule was rewritten as the performance requirement you see today. So the absence of a load plate on your mezzanine is not, by itself, a violation. What matters is whether the surface can carry what you are actually putting on it, and whether you can show how you know.

"Intended" is a decision you make, not a property of the floor

The phrase that does the work in 1910.22(b) is "maximum intended load." It is easy to read past it, but it is the heart of the rule. A mezzanine does not have one fixed intended load the way a bolt has a tensile strength. The intended load is the combination of what you decide to store there, how densely, plus the people and equipment that go up to handle it.

That cuts two ways. It means a mezzanine built for light storage is not out of compliance simply because it could not hold a pallet of tile; nobody intended it to. It also means the moment you change what goes up there, you have changed the intended load, and the question of whether the structure can carry it is open again. A loft that comfortably held empty display fixtures in July is a different surface, for the purposes of this rule, when it holds cases of bottled product in late November.

The practical failure is rarely a single dramatic overload. It is creep. The mezzanine was built years ago, possibly by a previous tenant, for a purpose nobody remembers. Each season a little more goes up. Heavier items replace lighter ones because they fit the shelving. A second set of shelving units is added. Nobody ever made a decision to raise the load; it just rose. That is exactly the situation the word "intended" is meant to force you to confront, because if you never decided what the mezzanine is for, you cannot say it supports its maximum intended load.

Finding out what your mezzanine was built to hold

You do not need to calculate a load capacity yourself, and you should not try to estimate one by eye. What you need is the information that already exists, or a qualified person to produce it if it does not.

Start with paperwork. A purpose-built steel mezzanine usually came from a manufacturer or installer, and the order documents, drawings or a capacity plate on a column often state the design load. If the mezzanine was part of the building, the building plans, permit set or landlord's records may show it. Your landlord or property manager is worth a direct question, especially if a prior tenant built the structure, because they may hold drawings you have never seen. A local building department sometimes has permit records for mezzanines added after construction.

If none of that turns up anything, the honest answer is that you do not know what the structure can carry, and the person who can tell you is a structural engineer. That is not a consultant retainer; it is a single visit to look at a single structure and give you a number in writing. For a small business deciding whether to keep loading a platform that people walk on and work under, it is the cheapest certainty available.

Once you have a design load, write it down somewhere people will see it. The current rule does not require a posted plate, but a sign at the top of the stairs stating what the mezzanine is rated for, and what it is meant to store, is the simplest way to keep the next person from adding a pallet of something heavy without thinking. It turns your intended load from an idea in your head into an instruction the whole crew can follow.

The holiday load, in practice

When you have a number, the seasonal question becomes manageable. Before the overflow goes up, ask what is actually going there. Product weight is printed on most case labels and on the packing list, so an approximate total for what you plan to store is usually easy to work out. Compare that against the rated capacity, and remember the rating is about distribution as well as total weight. A design load is normally stated per square foot of floor, so a dense stack in one corner can exceed it even when the total would fit if spread across the whole deck. Keep heavy items low and spread out rather than concentrated.

Remember what else is up there. People, the pallet jack or hand truck someone carried up, shelving units and the stored material itself all count. If you plan to move pallets onto the mezzanine with a forklift through a pallet gate, the point load at the edge where the pallet lands is exactly the kind of thing the original design may or may not have anticipated, and that is a question for the paperwork or the engineer, not for the operator.

Then look at how it is stored, which is where 1910.22(b) meets another rule. Under 29 CFR 1910.176(b), "storage of material shall not create a hazard," and material stored in tiers must be "stacked, blocked, interlocked and limited in height so that they are stable and secure against sliding or collapse." On a mezzanine, an unstable stack is a hazard twice over: to the people picking from it and to anyone below if it goes over the edge. Keeping stacks well back from open edges and stair openings is part of the same decision.

Inspection is already required. Add the load to it.

You do not need a separate program for this. Under 1910.22(d)(1), walking-working surfaces must be "inspected, regularly and as necessary, and maintained in a safe condition," and under 1910.22(d)(2) hazardous conditions must be corrected or repaired before an employee uses the surface, or guarded until they are. A mezzanine is a walking-working surface, so it is already on your list. The seasonal load change is precisely the "as necessary" moment.

When you walk it, look for the things that tell you a structure is being asked for more than it should carry: decking that sags or flexes underfoot, bent or twisted joists or beams, connections that look stretched or have shifted, cracks in concrete toppings, columns that have been struck by forklifts at floor level, and loose or missing fasteners. Any of those is a reason to take weight off before anyone goes back up, not after the rush.

Downstairs matters as well. Mezzanine columns in a working warehouse take hits from forklifts and pallet jacks. A damaged column changes what the deck above can safely hold regardless of what the original rating said. If you protect your racking uprights with guards, the mezzanine columns deserve the same attention.

A simple standard to hold yourself to

None of this makes you compliant on its own, and it is not legal advice. But a small business can meet the intent of 1910.22(b) with a short, honest routine. Know the design load of every elevated surface people walk on, from paperwork or from an engineer. Decide what each one is for and write that down where people will see it. Before the seasonal overflow goes up, check that what you plan to store, plus the people and equipment handling it, stays within that rating and is spread sensibly. Walk the structure as part of your regular walking-working surface inspections, and take the load off if you see signs of distress.

The question an inspector, an insurer or your own crew is entitled to ask is not "is there a plate on the column?" It is "how do you know this floor can hold what you put on it?" If you can answer that in one sentence, you are in a far better place than most of the mezzanines that fill up every November.

Related reading: Mezzanine Guardrails and Toeboards: What OSHA 1910.29 Actually Measures | Pallet Racking and Storage Safety: What OSHA Expects Under 29 CFR 1910.176 | Snow and Ice Are Written Into the Rule

OSHA standards cited

Always verify current OSHA standards at osha.gov. This article reflects standards in effect at the date of publication.

Not sure where you stand?

Take the 5-minute compliance assessment. Answer a few questions about your business and get a prioritized list of what OSHA expects, free.

Start free assessment