Using a Forklift to Lift a Worker: What 1910.178(m)(12) Says About the Platform on the Forks
A pallet and a ratchet strap are not a work platform. See what OSHA 1910.178(m)(12) requires before a forklift lifts a person to reach a high shelf or fixture.
A light fixture is out in the back corner of the warehouse, twenty feet up, and the lift that would normally reach it is not on site. The forklift is right there. Someone grabs an empty pallet, sets it on the forks, and a coworker steps onto it with a bulb in one hand. It takes four minutes, nobody has ever been hurt doing it, and it is exactly the kind of shortcut that shows up in an inspector's notes as a citation and in an incident report as something much worse.
This post answers one narrow question: what does OSHA actually require before a forklift may be used to raise a person? It is a different question from whether your operators are trained, which we cover in our posts on forklift operator retraining triggers and general forklift safety. Here the truck may be perfectly well run. The problem is what is riding on the forks.
A forklift is built to carry loads, not people
Start with the default rule. The powered industrial truck standard, 29 CFR 1910.178, prohibits riding on trucks except where a safe place to ride has been provided. Under 1910.178(m)(1), unauthorized personnel are not to be permitted to ride on powered industrial trucks, and where riding is authorized, a safe place has to be provided. A stand-alone pallet balanced on the tines is not a safe place by any reading of that sentence.
The reason is mechanical, not bureaucratic. A forklift's stability depends on the load sitting low and close to the mast, with the operator's weight and the counterweight balancing it. Raise the load high, add a person who shifts their weight, and the truck's center of gravity moves in ways the operator cannot feel from the seat. The mast can tilt, the forks can slide, a pallet can walk off the carriage. The person on top has nothing to hold and nowhere to go, and the fall is from whatever height they were lifted to.
What 1910.178(m)(12) requires
The standard does not forbid elevating a person with a forklift outright. It sets conditions. Section 1910.178(m)(12) requires a safety platform firmly secured to the lifting carriage or forks whenever personnel are elevated with a fork truck. It adds two more requirements: there must be a means for the person on the platform to shut off power to the truck, and protection from falling objects must be provided as necessary.
Each of those phrases does work, so it is worth taking them one at a time.
A safety platform, firmly secured. This means a purpose-built work platform, not a repurposed shipping pallet. The word "secured" is the heart of it. The platform has to be attached to the carriage or forks so it cannot slide, tip, or be knocked free. Plenty of manufacturers sell platforms that are designed to be fastened to the forks with pins, chains, or clamps, and many include guardrails, a toe board, and a gate. A platform that relies on gravity and friction to stay in place is not firmly secured, however carefully it was positioned.
A way for the person aboard to cut power. The worker on the platform is the one who sees the hazard first, whether it is a wire they are about to touch or a roof truss closing in on their head. The standard expects them to be able to stop the truck without relying on a shouted instruction that the operator might not hear over the engine. How you meet that requirement depends on the platform and truck, and it is a question for the equipment manufacturer or dealer.
Protection from falling objects. If anyone, or anything, can be above the platform, the person on it needs overhead protection. A worker lifted to a high rack beneath other pallets is a good example.
Notice what the standard does not say. It does not say a trained operator can eyeball it, and it does not say a pallet with a strap is close enough. The conditions are specific, and an inspector will ask about them specific by specific.
Check the manufacturer before you buy a platform
Having a platform that satisfies the wording of 1910.178(m)(12) is necessary, but it is not the whole analysis. The truck itself has to be suitable for the job. Lift trucks have a rated capacity that accounts for the load center and the lift height, and that capacity is stated on the data plate. The weight of the platform, the worker, and any tools all count against it, and the rating is reduced when the load center moves outward. Under 1910.178(a)(4), modifications and additions that affect capacity and safe operation need the manufacturer's prior written approval, which is a reason to ask the dealer before fitting a platform rather than after.
Practical questions to put to the manufacturer or dealer include: does this truck model allow personnel platforms at all, what is the derated capacity with the platform fitted, what height is permitted, and what restraint does the maker expect the worker to use. If the manufacturer says no, the answer is no, and the better solution is the next section.
Often the right tool is a different tool
The honest advice for most small employers is not to buy a platform at all. A vehicle designed to lift people carries protections a forklift does not: guardrails built into the basket, controls at the person's fingertips, outriggers or a stability design aimed at elevated work. Scissor lifts and boom lifts are covered by their own rules, which our post on aerial and scissor lift safety walks through for construction work and the general industry equivalent in 1910.67 for vehicle-mounted platforms. Renting one for a day is frequently cheaper than a single hour of downtime after an injury, and it removes the question of whether your improvised setup meets the standard.
If you do choose the forklift route because you do this work regularly, treat it as a defined task with its own written procedure. That procedure should say which truck, which platform, who may operate it, who may ride, and what the limits are. It is the same logic as a permit for any hazardous job: the decision gets made on purpose, in advance, rather than on the spot by whoever is nearest.
Rules for the day you do lift someone
Where a compliant platform and approved truck are in place, a few operating habits make the difference between a controlled lift and a near-miss.
The operator stays at the controls the whole time the platform is raised. Section 1910.178(m)(5) addresses unattended trucks, and in practice that means the operator should not walk away from a truck with a worker aloft, even to fetch something. The worker on the platform is also, in effect, a rider, so the rest of the traffic rules still apply: no one passes under the elevated portion of the truck, a point 1910.178(m)(2) states plainly for loaded and empty forks alike.
Travel with a raised platform should be limited to what is necessary, slow, on a level surface, and with the mast tilted as the manufacturer allows. The route should be walked first for overhead hazards like sprinkler pipes, conduit, and doors, because the platform's top edge is now well above the operator's usual sight line. Floors matter as well. A crack, a drain grate, or a dock edge that a loaded truck would handle can tip a raised platform.
Lastly, the person on the platform should be trained for it. Your forklift operator training under 1910.178(l) covers the operator, not the rider, so include a short briefing for anyone who will be lifted: what to hold, where to stand, how to signal, and how to shut the power off.
What to do this week
Walk the building and ask a plain question: has anyone here ever been lifted on the forks, on a pallet, in a bucket hung from a chain, or in a bin? If the answer is yes, find out how often and why. That reason, a light fixture, an inventory count, a sign, a security camera, is the real job to solve, and it can almost always be solved with the right equipment instead of an improvised one.
Then write the rule down and tell people. A short sentence in your forklift program is enough: forklifts are not used to lift people unless a manufacturer-approved platform is fitted and the written procedure is followed. It is the sort of clear line that protects a good employee from a bad shortcut on a busy afternoon.
If you keep a forklift inspection routine, add the platform to it. Our forklift daily inspection checklist covers the pre-shift points 1910.178(q)(7) expects you to document for the truck itself, and a fastening point that has worked loose is just the sort of thing a daily look can catch.
This article is general information, not legal advice, and following it does not guarantee compliance. Confirm requirements against the current text of the standard and your equipment manufacturer's instructions.
Related reading: The Forklift Pre-Shift Inspection OSHA Actually Requires | Forklift Safety Basics: What OSHA 1910.178 Actually Requires of Small Businesses | Your Forklift Operators Were Certified Once — OSHA Wants to Know What's Happened Since
OSHA standards cited
- 29 CFR 1910.178
General Industry Standards
- 29 CFR 1910.67
General Industry Standards
Always verify current OSHA standards at osha.gov. This article reflects standards in effect at the date of publication.
Not sure where you stand?
Take the 5-minute compliance assessment. Answer a few questions about your business and get a prioritized list of what OSHA expects, free.
Related Articles
Continue learning about OSHA compliance and workplace safety
Equipment Safety
What Goes on an Aerial Lift Pre-Start Inspection? A Free Checklist From The Lift Bros, Item by Item
A free aerial lift pre-start inspection checklist from The Lift Bros, item by item, and the OSHA rule behind it: 1926.453 for booms, 1926.451 for scissors.
Equipment Safety
The Fan on the Floor Is a Machine: What OSHA 1910.212(a)(5) Requires of Fan Blade Guards
OSHA 1910.212(a)(5) says fan blades under seven feet from the floor or working level need a guard with openings no larger than half an inch. What that means.
Equipment Safety
When Was That Floor Jack Last Inspected? What OSHA 1910.244 Requires of Jacks in a Small Shop
OSHA 1910.244(a) sets rules for jacks: a marked rated load, cribbing once the load is up, a six-month inspection, and tagging bad jacks. What small shops owe.