Who Walks the Job Site? What 1926.20(b) Means by Frequent and Regular Inspections by a Competent Person
OSHA 1926.20(b)(2) requires frequent, regular job site inspections by a competent person you designate. Learn who qualifies and how to document it.
A remodeling contractor has three crews working this week: a kitchen gut in one house, a deck rebuild across town, and a small commercial tenant improvement downtown. The owner is on the phone with a supplier most of the day, and each crew lead is busy hanging drywall, framing, or running conduit. Ask who is responsible for walking each site to look for problems, and you will usually get a shrug followed by "we all keep an eye out." That answer feels reasonable. It is also exactly the gap that one short paragraph of the construction rules is written to close.
This post answers one question: what does 29 CFR 1926.20, titled General safety and health provisions, require when it says job sites must be inspected, and what does it take to meet that requirement on a small crew? For the narrower inspection duties that apply to specific hazards, see our posts on soil classification for trenches under 1926.652 and construction housekeeping under 1926.25.
What the paragraph actually says
Paragraph (b) of 1926.20 is headed Accident prevention responsibilities. Subparagraph (b)(1) makes it the employer's responsibility to initiate and maintain the programs necessary to comply with the construction standards. Subparagraph (b)(2) is the one that matters here: those programs must provide for frequent and regular inspections of the job sites, materials, and equipment, made by competent persons designated by the employer.
Read that sentence slowly, because each phrase does work. "Frequent and regular" means the inspections are not a one-time event at the start of a job and not something you do only after someone is hurt. "Job sites, materials, and equipment" means the walk covers three things, not one: the conditions of the work area, the stock and supplies on hand, and the tools and machines in use. "Competent persons designated by the employers" means someone has to be chosen. A general sense that everyone is watching does not satisfy a rule that asks for a designation.
The standard does not say how often "frequent" is, and it does not say the inspection has to be written down. Where a specific construction standard sets a frequency, that frequency controls for that hazard. Excavations, for example, must be inspected by a competent person before work starts and as needed through the shift under 1926.651(k), and scaffolds must be inspected by a competent person before each work shift under 1926.451(f)(3). Paragraph 1926.20(b)(2) is the general rule underneath those specific ones, and it applies to everything those specific rules do not reach.
Who counts as a competent person
The construction standards define the term in 1926.32(f). A competent person is one who is capable of identifying existing and predictable hazards in the surroundings or working conditions that are unsanitary, hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.
Two halves, and both are required. The first is knowledge: the person can recognize a hazard when they see it, including one that has not yet hurt anyone but plausibly could. The second is authority: the person is allowed to stop work or fix the problem without waiting for permission. A veteran carpenter with sharp eyes who has no power to halt a crew is half a competent person. A project manager with all the authority and no ability to spot an unguarded floor opening is the other half.
For a small contractor, this usually points to the crew lead or foreman on each site, or to the owner on jobs where the owner is present. The designation does not require a certificate or a particular course. It does require that the person actually has the capability the definition describes, and that the employer has told them they have the authority. If your foreman would need to call you before sending a worker down off an unprotected edge, the authority half is missing in practice, whatever your intentions.
Some specific standards add their own training expectations for the competent person on that hazard, such as excavation and scaffold work. Check the standard that governs the work in front of you rather than assuming the general definition is the whole story.
Why a designation matters on a site you do not control
Small contractors often work on sites where other trades are present, or on a homeowner's property that changes daily. Conditions change between the morning and afternoon. A subcontractor leaves a cord across a walkway, a delivery blocks an exit path, a guardrail comes off to move material and is not put back.
A designated person turns that churn into a routine. Someone knows it is their job to look, so the look actually happens. When something is found, the same person has the authority to correct it, or to remove a damaged tool from service. The standard backs that up in 1926.20(b)(3), which says that machinery, tools, materials, or equipment not in compliance with an applicable requirement of the construction standards is prohibited, and must either be identified as unsafe by tagging or locking the controls to make them inoperable, or be physically removed from the place of operation. In practice, that means an inspection that finds a frayed cord or a cracked ladder rail has to end in an action, not just a note.
There is also a training layer. Under 1926.21(b)(2), the employer must instruct each employee in the recognition and avoidance of unsafe conditions and the regulations applicable to their work environment. A crew that has been told what the competent person is looking for, and why, tends to report problems to that person instead of working around them.
Building a routine that fits a three-person crew
Nothing here requires software or a binder as thick as a phone book. It requires a few decisions made once and repeated.
Start by naming the person for each site, in writing, even if the writing is a short note in your safety file. Say who they are, which jobs they cover, and that they are authorized to stop work and correct hazards. When the foreman is out sick, name who steps in. A designation that lapses whenever someone takes a day off is a designation with holes in it.
Next, decide when the walk happens. A sensible pattern is a quick look before work begins each day, because conditions overnight may have changed, and another look when something significant changes: a new trade arrives, a crane or lift shows up, the weather turns, a phase of the job ends and a new one begins. Where a specific standard sets a stricter schedule for a hazard on your site, follow that schedule for that hazard.
Then decide what the walk covers, and keep it tied to the three things the standard names. For the site: walking surfaces, openings and edges, access and egress, housekeeping, overhead work above people, and any excavation or scaffold. For materials: how stock is stacked and stored, flammables, and anything that has been delivered damaged. For equipment: tools, cords, ladders, and machines, checked against what the manufacturer expects and what the applicable construction standard requires.
Finally, decide what happens when the walk finds something. The fix is made, the item is tagged out or removed, or the work stops until the hazard is controlled. Writing down what was found and what was done is not demanded by 1926.20(b)(2) itself, but it is how you show later that the inspections were frequent and regular and not just intended. A one-line entry with a date, the site, what was found, and what was done is enough to tell the story. If you want a template for the broader practice, our post on workplace self-inspections for small businesses walks through one.
What this does not do
An inspection routine does not, on its own, make a job site compliant. The competent person has to be capable and empowered in fact, the findings have to be acted on, and the specific standards for fall protection, excavation, electrical work, and the rest still apply on their own terms. Penalties and enforcement depend on the facts of a particular site, and the standards change, so read 1926.20 and 1926.32 directly on osha.gov and check your state plan if you operate in a state that runs its own program, since state plans can be stricter.
What the routine does give you is an answer to the question at the top of this post. When someone asks who walks your job sites, the answer is a name, a schedule, and a habit of fixing what they find, rather than a shrug.
Related reading: Fall Protection in Construction Under 1926.501 | Construction Housekeeping Under 1926.25 | Workplace Safety Self-Inspections
OSHA standards cited
- 29 CFR 1926.20
Construction Industry Standards
- 29 CFR 1926.652
Construction Industry Standards
- 29 CFR 1926.25
Construction Industry Standards
- 29 CFR 1926.651
Construction Industry Standards
- 29 CFR 1926.451
Construction Industry Standards
- 29 CFR 1926.32
Construction Industry Standards
- 29 CFR 1926.21
Construction Industry Standards
- 29 CFR 1926.501
Construction Industry Standards
Always verify current OSHA standards at osha.gov. This article reflects standards in effect at the date of publication.
Not sure where you stand?
Take the 5-minute compliance assessment. Answer a few questions about your business and get a prioritized list of what OSHA expects, free.
Related Articles
Continue learning about OSHA compliance and workplace safety
Inspections
How to Run a Workplace Safety Self-Inspection That Actually Finds Problems Before OSHA Does
A structured safety self-inspection helps small businesses find OSHA violations before inspectors do. Here's how to build and run one that produces real results.
Inspections
Are You On OSHA’s 2025 Site Specific Targeting List
OSHA refreshed its Site Specific Targeting program for 2025. See how 300A data drives selection and what to do before an inspector arrives.
Inspections
The Walkaround Rule After Year One: How To Prepare Your Front Of House And Keep Inspections Productive
OSHA’s walkaround rule lets employees designate a representative during inspections. Learn how non union employers should prepare and keep visits productive.