Snow and Ice Are Written Into the Rule: What OSHA 1910.22(a)(3) Asks of Your Dock, Doorways and Walkways on a Frozen Morning
OSHA 1910.22(a)(3) names snow and ice as hazards walking-working surfaces must be kept free of. What that means for small shops on the first frozen morning.
The first hard freeze usually arrives overnight. The owner of a small distribution shop pulls in at six, finds the back lot glazed, and watches the first employee of the day pick her way from her car to the side door with one hand on the building. Inside, the dock plate is wet with meltwater from yesterday's trucks, and the rubber mat at the side door is already soaked through. Nobody has been hurt. Nobody has decided whose job it is to deal with any of this, either.
This post answers one narrow question: what does OSHA's general industry walking-working surfaces standard actually say about snow and ice, and what does it ask a small employer to do on mornings like that one? The broader rules on floor holes, guardrails and the four-foot fall protection trigger are covered in our post on walking-working surfaces, and everyday indoor slips are covered in slip, trip and fall prevention for small warehouses and shops. Winter is its own problem, because the hazard is created by the weather, it appears overnight, and it often appears on surfaces nobody thinks of as part of the workplace.
The words are already in the standard
Many owners assume ice is an act of nature that OSHA has nothing to say about. The standard disagrees. Paragraph 1910.22(a)(3) requires that walking-working surfaces be maintained free of hazards such as sharp or protruding objects, loose boards, corrosion, leaks, spills, snow, and ice. Snow and ice are named, in the same list as a spill on the shop floor.
The paragraphs around it fill out the picture. Paragraph (a)(1) requires places of employment, passageways, storerooms, service rooms and walking-working surfaces to be kept clean, orderly and sanitary. Paragraph (a)(2) requires the floor of each workroom to be kept clean and, to the extent feasible, dry, and where wet processes are used, requires drainage and, to the extent feasible, dry standing places such as platforms or mats. Meltwater tracked in from a dock door is not a "wet process" in the usual sense, but the same idea applies to it: the floor inside the door is still a workroom floor that has to be kept dry where that is feasible.
Subpart D defines a walking-working surface broadly, as essentially any surface an employee walks or works on, or uses to reach a work area. That is why winter is harder than it looks. The loading dock apron, the exterior stairs to a mezzanine office, the path from the side door to the dumpster, the yard where an employee walks to the propane cage: if your people use these surfaces to do their jobs, they are the kind of surface the standard is written about. Whether a particular stretch of shared parking lot counts is a harder question, and if you are unsure about a specific area, OSHA's free on-site consultation program is a reasonable place to ask.
Inspect regularly and as necessary
The part of the standard that does the most work in winter is paragraph (d). Paragraph (d)(1) requires walking-working surfaces to be inspected regularly and as necessary, and maintained in a safe condition. "Regularly" is the routine walk you might do weekly. "As necessary" is the part winter tests, because conditions change between one shift and the next. An overnight freeze after a day of slush, freezing rain, a refreeze in the late afternoon when the sun leaves the dock: these are the moments when a surface that was fine yesterday is not fine now.
In practice that means someone has to look before the first employee uses the surface, not after. In a small business the most workable answer is a named person, usually whoever opens, with a short route they walk before anyone else arrives: the employee entrance, the dock, any exterior stairs, and whatever paths people use to reach equipment outside. The standard does not require a written log of these checks. A brief note of when the route was walked and what was done is still worth keeping, because it is the only way to show later that the check happened, and it tells you quickly whether the routine is actually being followed when the opener is out sick.
Correct it before anyone uses it, or close it off
Paragraph (d)(2) is the operational heart of the rule. It requires hazardous conditions on walking-working surfaces to be corrected or repaired before an employee uses the surface again. If the correction cannot be made immediately, the hazard must be guarded to prevent employees from using the surface until it is corrected.
Applied to ice, the first half is straightforward: clear it and treat it before people walk on it. That requires the means to be on hand before the first storm, not bought on the morning of it. A shovel, a supply of ice melt or sand, and somewhere dry to keep them near the doors are the whole kit for most small sites.
The second half matters when you cannot clear a surface in time. If the exterior stairs to the upstairs office are a sheet of ice at opening and the ice melt has not worked yet, the rule's answer is to stop employees from using them until they are fixed, for example by closing that door and routing people through another entrance. Two cautions apply. First, guarding has to actually prevent use. A cone at the top of a staircase that people still have to climb to reach their desks is not guarding. Second, check what you are closing. If the door you want to shut is a designated exit route, closing it off creates a different problem under OSHA's exit route rules in 1910.37, and the answer there is to clear it, not to block it. Our post on emergency lighting and exit routes covers those rules.
Paragraph (c) sits behind all of this. It requires the employer to provide, and ensure each employee uses, a safe means of access and egress to and from walking-working surfaces. If the only way onto the dock in the morning is across an unsalted apron, the problem is not just the ice. It is that there is no safe way in.
The dock, the doorway and the drift nobody owns
A few places cause most of the trouble in small operations, and each has a specific pattern.
The loading dock combines exterior ice, interior meltwater and moving equipment. Trailers bring in snow on their floors and drop it as slush where forklifts turn. Dock plates and bridge plates that are wet or icy are a hazard for the people walking across them as well as the trucks, and our post on dockboards and bridge plates under 1910.26 covers the separate requirements those plates carry. Keeping the dock dry usually means squeegeeing and mopping on a schedule during the shift, not once at close.
The doorway is where outside becomes inside. A mat at the entrance helps only while it is absorbing water; once it is saturated it is just a wet surface with edges that curl. Swapping or drying mats through the day is the kind of ordinary maintenance (a)(2) is pointing at.
The drift nobody owns is the leased site problem. Many small businesses rent, and the lease says the landlord handles snow removal. That arrangement is useful, but it does not change who is responsible for your employees. OSHA's obligations under 1910.22 sit with the employer whose employees use the surface. If the landlord's plow contractor does not arrive until nine and your shift starts at seven, the inspection and the decision about whether your people use that walkway are still yours. The practical answer is to know what your contract actually promises, to keep your own ice melt and shovel anyway, and to decide in advance which entrance staff use if the contractor is late.
Footwear, rooftops and what this post does not cover
Footwear is the question owners ask next. The general PPE standard, 1910.132, requires an employer to assess the workplace for hazards that call for protective equipment, and a hazard assessment that ignores outdoor ice for employees who work in the yard all winter is likely incomplete. Slip-resistant soles or strap-on traction devices can be part of the answer for outdoor work. They come with their own problem: cleats that grip ice can be slippery on smooth concrete or steel plate indoors, so employees who move in and out need a place and a habit for taking them off at the door. Our post on cold stress and PPE compatibility goes into how winter gear interacts with the rest of a worker's kit.
Rooftops are a separate question entirely. Shoveling snow off a roof or clearing drains on a flat roof is work at height, and the fall protection rules in 1910.28 apply to it. Paragraph 1910.22(b) also requires each walking-working surface to support its maximum intended load, which is worth thinking about before anyone walks onto a canopy or mezzanine roof carrying a drift. If your plan involves employees on a roof, treat it as a fall protection job first and a snow job second.
A winter routine that fits a small shop
None of this needs a binder. A routine that matches what the standard asks can be agreed in one conversation before the first storm: who walks the route at opening and what route that is; where the shovel and ice melt are kept, and who checks the supply; which entrances get closed, and which entrance everyone uses instead, when a surface cannot be cleared in time; how often the dock and the doorways get dried during a wet shift; and what employees should do when they find a hazard, which should be to report it and stay off it, not to work around it.
Following this will not by itself make any site compliant with every rule that touches walking-working surfaces, and state plans may set additional requirements. What it does is turn snow and ice from weather that happens to you into a condition someone looks for, fixes, or closes off before the first employee steps onto it, which is the sequence 1910.22(d) actually describes.
Related reading: Walking-Working Surfaces: The OSHA Standard Small Businesses Keep Getting Cited For | Slip, Trip, and Fall Prevention in Small Warehouses and Shops | Loading Dock Safety
OSHA standards cited
- 29 CFR 1910.22
General Industry Standards
- 29 CFR 1910.37
General Industry Standards
- 29 CFR 1910.26
General Industry Standards
- 29 CFR 1910.132
General Industry Standards
- 29 CFR 1910.28
General Industry Standards
Always verify current OSHA standards at osha.gov. This article reflects standards in effect at the date of publication.
Not sure where you stand?
Take the 5-minute compliance assessment. Answer a few questions about your business and get a prioritized list of what OSHA expects, free.
Related Articles
Continue learning about OSHA compliance and workplace safety
Hazard Control
Red Cans and Yellow Stripes: What OSHA's Safety Color Code Actually Requires in a Small Shop
29 CFR 1910.144 sets red for flammable-liquid cans and danger signs and yellow for caution and physical hazards. Here is what it asks of a small shop.
Hazard Control
Stairs in Your Shop or Warehouse: What OSHA 1910.25 Asks You to Measure
OSHA 1910.25 covers general industry stairs: riser and tread uniformity, headroom, handrails and stair rails. A walk-through for small shop owners.
Hazard Control
Mezzanine Guardrails and Toeboards: What OSHA 1910.29 Actually Measures
OSHA 1910.29 sets the height, strength and gap rules for guardrails and toeboards. What a small warehouse or shop owner needs to check on a mezzanine edge.