The Breaker Labeled 'Misc': What OSHA 1910.303(f) Requires of Your Panel Directory
OSHA 1910.303(f) requires each circuit to be legibly marked at its breaker or disconnect. What that means for a small shop's panel directory and motor switches.
The compressor in the back of your shop has stopped and a technician needs to swap the pressure switch. He opens the panel door to kill the circuit and finds the directory card: a column of handwriting from three owners ago. Breaker 7 says "shop." Breakers 12 and 14 say "misc." Two are blank, and one says "DO NOT TURN OFF" with no hint of what it feeds. He flips the one he thinks is right, the compressor goes quiet, and he starts work. What he does not know is that the compressor is fed from two places, and the one he left on is the one that actually feeds the controls he is about to put his hands in.
That scene is the question this post answers: what does OSHA actually require of the labels on your breakers and disconnect switches, and why does it matter for a business that has no electrician on payroll? The short version is that 29 CFR 1910.303(f) requires every circuit and every required disconnect to be legibly and durably marked with its purpose, unless the purpose is obvious from where it sits, and that this applies to old buildings as well as new ones. If you are looking for the rule about keeping the space in front of the panel clear, that is a separate paragraph, 1910.303(g), covered in our post on the boxes stacked in front of your electrical panel.
What 1910.303(f) says, paragraph by paragraph
Section 1910.303 is the general requirements section of OSHA's electrical standard for general industry, Subpart S. Paragraph (f) is headed "Disconnecting means and circuits," and the parts that matter to most small shops are the first four.
Paragraph (f)(1) covers motors and appliances. Each disconnecting means that Subpart S requires for a motor or an appliance has to be legibly marked to indicate its purpose. The exception is narrow: no marking is needed where the disconnect is located and arranged so that its purpose is evident. A fused switch bolted to the side of the only machine in a room, with the conduit running straight into that machine, is probably evident. A bank of six identical switches on a wall feeding equipment across the building is not.
Paragraph (f)(2) covers services, feeders and branch circuits. Each one has to be legibly marked to indicate its purpose at its disconnecting means or overcurrent device. In a typical small business, that overcurrent device is the circuit breaker in the panel, and the marking is the panel directory or a label at the breaker itself. The same exception applies: if the location and arrangement make the purpose evident, no marking is required. In a panel of thirty or forty breakers, the location and arrangement almost never make anything evident.
Paragraph (f)(3) says these markings must be durable enough to withstand the environment they are in. A paper card in a dry office panel may hold up. The same card inside a panel in a wash-down area, a body shop, or an unheated warehouse may be illegible within a season. Marker on painted steel that rubs off the first time someone wipes the door does not meet this.
Paragraph (f)(4) requires that disconnecting means required by Subpart S be capable of being locked in the open position. This one comes with a date. Under 1910.302(b)(4), (f)(4) applies to installations made after August 13, 2007. Paragraphs (f)(1) through (f)(3), by contrast, are listed in 1910.302(b)(1) as applying to all installations regardless of when they were designed or installed. That distinction matters for small businesses in older buildings: the panel may predate the lockable-disconnect requirement, but the labeling requirement still applies to it today.
"Evident" is a higher bar than it sounds
The exception in (f)(1) and (f)(2) is the part most owners lean on, usually without realizing it. "Everybody knows breaker 3 is the coffee machine" is not location and arrangement. It is memory, and memory leaves when the person holding it does.
A useful test is to imagine the person who will rely on the marking. It is not you. It is an outside electrician on a Saturday, a new maintenance hire, or a firefighter who needs to cut power to one part of the building without blacking out the rest. Could that person, standing at the panel with no one to ask, tell which breaker feeds which load? If the answer depends on someone else being there, the purpose is not evident.
Descriptions also have to say something. "Shop," "misc," "lights," and "spare" are technically markings, but they do not indicate purpose in any way that helps the person at the panel. "Spare" is a particular problem when the breaker is on and feeding something. A label that is wrong is worse than a blank, because it invites someone to trust it.
The National Electrical Code, which your electrician and local building inspector work from, has its own and more detailed rules for identifying circuits in a panelboard. Those sit alongside OSHA, not in place of it, and a licensed electrician is the right person to tell you what your local code expects for new or altered work.
Why this is a lockout problem, not a paperwork problem
Labels feel like housekeeping. They are actually the first step of every safe repair in your building.
When someone services a machine, OSHA's lockout/tagout standard, 1910.147, expects the work to follow an energy control procedure that identifies how to shut down and isolate that machine from its energy sources. Isolation starts with knowing which device controls which equipment. If the directory is wrong or blank, the person doing the work either guesses, or switches things off one at a time until the right machine stops, which is how equipment fed from more than one circuit ends up partially live. Our post on the six parts of a compliant energy control program covers the procedure itself.
The same applies to electrical work on the circuits themselves. OSHA's safe work practices standard, 1910.333, generally expects live parts to be deenergized before employees work on or near them, and deenergizing a circuit means first being able to find it. We wrote separately about what 1910.333 says about deenergizing first; none of it works if the breaker you open is not the one feeding the work.
There is also a slower risk. Small businesses add circuits over time: a new compressor, a second walk-in cooler, an EV charger in the lot, a tenant fit-out. Each addition is a chance for the directory to fall behind reality. A panel that was labeled correctly when the building was wired can be wrong a decade later without anyone touching the paper.
Getting your panels right without hiring a consultant
Start by finding every panel and every motor or equipment disconnect in the building. Include the subpanel in the back room, the disconnect on the roof for the HVAC unit, and the switch on the wall beside the large equipment. Many owners discover a panel they did not know they had.
Then compare the directory against reality. This is the step that needs a qualified electrician, because the reliable way to trace a circuit is to deenergize it and see what goes off, and in a working business that means planning around production, refrigeration and anything on life-safety circuits. Ask the electrician to note any equipment fed from more than one breaker, because that is exactly what your lockout procedures need to know. Do not have an untrained employee start flipping breakers to find out.
Write the new labels for the person who has never been in your building. Name the load and its location: "Air compressor, back wall, 240V," "Walk-in cooler condenser, roof," "Front office receptacles, north wall." Where a breaker truly feeds nothing, mark it as off and unused rather than "spare." Use a printed directory or label that will survive the room it is in, and protect it from moisture or grease where that applies. Label the motor and equipment disconnects too, not just the breakers, unless the disconnect is plainly part of the machine it serves.
Finally, make updating the directory part of every electrical change. Whoever adds or moves a circuit updates the label before they leave. It costs nothing on the day and saves the guesswork later. Your regular workplace self-inspection is a natural place to glance at each panel door and check that the directory is still there and still readable.
What this does and does not get you
A correctly marked panel does not make your electrical system compliant on its own. Subpart S covers grounding, guarding of live parts, working clearances, cords and much more, and a label cannot fix a damaged breaker or a missing dead-front cover. If your panel predates 2007, it may not accept a lock on every disconnect, which is worth discussing with your electrician as part of your lockout planning.
What labeling does is make every other electrical safety step possible. It is one of the few OSHA requirements a small business can meet in an afternoon with an electrician and a label maker, and it is the one the next person at the panel will be relying on without knowing it.
Related reading: The Boxes Stacked in Front of Your Electrical Panel Are an OSHA Violation | Can Your Electrician Just Work the Panel Live? | What 1910.147 Requires
OSHA standards cited
- 29 CFR 1910.303
General Industry Standards
- 29 CFR 1910.302
General Industry Standards
- 29 CFR 1910.147
General Industry Standards
- 29 CFR 1910.333
General Industry Standards
Always verify current OSHA standards at osha.gov. This article reflects standards in effect at the date of publication.
Not sure where you stand?
Take the 5-minute compliance assessment. Answer a few questions about your business and get a prioritized list of what OSHA expects, free.
Related Articles
Continue learning about OSHA compliance and workplace safety
Electrical Safety
Your Own Crew Is Remodeling the Shop: What OSHA 1910.304(b)(3)(ii) Requires of GFCI Protection on Temporary Power
OSHA 1910.304(b)(3)(ii) requires GFCI protection on temporary power during maintenance, remodeling and repair. What it means when your own staff do the work.
Electrical Safety
Dark by Four O'Clock: What OSHA 1926.405(a)(2) Requires of the Temporary Lights on Your Jobsite
29 CFR 1926.405(a)(2) sets the rules for temporary jobsite lighting: guarded lamps, no hanging by the cord, hard-usage cords and wet-location limits on site.
Electrical Safety
Can Your Electrician Just Work the Panel Live? What OSHA 1910.333 Says About Deenergizing First
OSHA 1910.333(a) says live parts must be deenergized before anyone works on or near them. See the narrow exceptions and what to do before a panel opens.