Skip to main content
Electrical SafetyReviewed against current OSHA standards

Can Your Electrician Just Work the Panel Live? What OSHA 1910.333 Says About Deenergizing First

OSHA 1910.333(a) says live parts must be deenergized before anyone works on or near them. See the narrow exceptions and what to do before a panel opens.

Updated November 5, 2026
6 min read
By the WorkSafely safety team

A breaker in the back office keeps tripping, and the electrician your landlord recommended is standing in front of the panel with the cover already off. It is a Tuesday, the shop is busy, and he says he can find the problem faster if nobody shuts the power down. You would like to say yes. Every minute of downtime costs you something, and he has done this a thousand times.

This post answers one narrow question: when is it acceptable under OSHA's general industry rules for someone to work on a live electrical panel or circuit? The short version is that the default answer is no, and the exceptions are narrower than most owners assume. The rule is 29 CFR 1910.333, titled "Selection and use of work practices." It is a different standard from the ones that govern how your wiring and panels are installed, which we cover in our post on electrical safety under 1910.303, and it is different again from the lockout rule for machinery. It governs how people behave around electricity.

The default: turn it off before anyone touches it

Paragraph (a)(1) of 1910.333 states the basic rule: live parts to which an employee may be exposed must be deenergized before the employee works on or near them. The word "near" matters. The rule is not limited to touching a conductor. It covers working close enough that an employee could be exposed to the hazard those parts present.

The standard then gives the employer a way out, but only on a showing. Energized work is allowed when the employer can demonstrate that deenergizing introduces additional or increased hazards, or that it is infeasible because of equipment design or operational limitations. The examples OSHA gives are the kind of things that cannot simply be switched off: life support systems, ventilation in hazardous locations, and emergency alarm systems. Testing and troubleshooting of circuits that can only be tested while live is the other common category.

Notice what is not on that list. Convenience is not on it. Avoiding a production stoppage is not on it. A customer who needs the lights back on is not on it. If the reason to work live is that shutting down is inconvenient, the exception does not apply, and the electrician is being asked to take a risk that the standard does not recognize as justified.

There is also a carve-out for low voltage. Live parts that operate at less than 50 volts to ground do not have to be deenergized, provided there will be no increased exposure to electrical burns or to explosion from electric arcs. That covers a good deal of low-voltage control wiring, but it does not cover the building's 120/208 or 277/480 volt panels, which is what almost every small business has behind the breaker door.

Who may work on something that is still live

When the exception does apply, paragraph (a)(2) says other safety-related work practices must be used to protect employees, and paragraph (c) of the same section sets the conditions for working on or near exposed energized parts. The most important condition is that only qualified persons may work on electric circuit parts or equipment that have not been deenergized.

"Qualified person" is a defined term, and it is about training, not job title. Under the related training standard, 1910.332, employees who face a risk of electric shock that the installation requirements of the electrical design standards do not reduce to a safe level must be trained in the safety-related work practices that apply to them. The more exposure a task involves, the more detailed the training has to be. A person who is licensed as an electrician has probably had that training, but you should not assume it, and if you hire a contractor the question is worth asking out loud. Our enterprise site has a longer treatment of why qualification attaches to the task and not the title, and the same logic applies to a one-location shop.

This is also where your own employees come in. The office manager who resets a breaker is generally not doing the kind of work this section is aimed at, but the maintenance person who takes a cover off a disconnect to see why a machine will not start may be. If someone on your staff is opening energized equipment, the standard expects them to be qualified for that task. If nobody on staff is, the right procedure is that nobody on staff opens it.

When the power is off, how do you know it is off?

Most of the real safety value in this standard sits in paragraph (b), which applies to work on exposed deenergized parts, or near enough to them to be exposed to the hazard. It requires that while an employee is exposed to contact with parts of fixed electric equipment or circuits that have been deenergized, the circuits energizing those parts must be locked out or tagged or both, following the requirements of that paragraph.

Three ideas follow from that for a small business. The first is that someone has to have a written or at least well understood procedure for shutting the equipment down, and that procedure has to identify the sources of power. A panel can be fed from more than one place, and a tenant space can be fed from a disconnect in a different part of the building. The second is that a qualified person is expected to verify, with test equipment, that the circuit is actually dead before work starts. Opening a breaker and assuming the circuit is dead is the classic way an experienced person gets hurt. The third is that the lock or tag stays on until the work is done and the person who applied it is the one who removes it, so that a coworker does not restore power while someone's hands are inside the enclosure.

Do not confuse this with the machinery lockout rule. 1910.147, Control of Hazardous Energy, is the standard for servicing and maintaining machines and equipment, and it has its own exclusions. Exposed fixed electrical circuits, such as the inside of a panel, are handled by 1910.333(b). The two standards overlap in practice because a machine may have both a mechanical hazard and an electrical one, and a good procedure treats them together. Our post on outside service technicians and lockout covers the contractor coordination side of the same problem.

A practical routine before anyone opens a panel

What does this mean on a normal Tuesday? A few habits change the answer when the electrician is standing at the panel.

Ask the question before the cover comes off: does this work require the circuit to be live? Most of the time it does not. Replacing a breaker, adding a circuit, swapping a disconnect, and repairing a fixture can all be done dead. Troubleshooting is the common reason people argue for live work, and even then, the energized portion is often a short measurement, followed by shutting down for the actual repair.

Ask the contractor how they will verify the circuit is deenergized and how they will lock or tag it. A reputable electrician will have an answer that does not take long. If the answer is vague, that tells you something about the rest of the job.

Know where your power comes from. Many owners cannot say which disconnects feed their space, and that is a hazard in its own right, because a procedure that depends on finding the right switch in an emergency will not work. Label the main disconnect and the panels, and keep the area around them clear, which is the subject of our post on panel clearance and working space.

Keep a short note of who did the work and when. OSHA does not prescribe a form for this, but a record of who verified the power was off, and who locked it, is the kind of evidence that shows the practice is real if anyone later asks.

What the standard does not tell you

Reading 1910.333 does not tell you whether a given job is safe, and following this post will not make a workplace compliant. The standard leaves several things to your judgment and your contractor's: whether an exception truly applies, what protective equipment fits a particular task, and how the hazard changes with the equipment's voltage and condition. Those decisions deserve a qualified person, and sometimes a call to the electric utility or to your state's occupational safety agency if you operate in a state plan jurisdiction.

What the standard does give you is a clear order of operations. Turn it off first. Prove it is off. Keep it off with a lock or a tag. And if there is a real reason it cannot be turned off, make sure the person working on it is qualified for that task. A short conversation at the panel, before the cover comes off, is the cheapest control on the list.

Related reading: Electrical Safety Under OSHA 1910.303 | Lockout and Outside Service Technicians | Panel Clearance and Working Space

OSHA standards cited

Always verify current OSHA standards at osha.gov. This article reflects standards in effect at the date of publication.

Not sure where you stand?

Take the 5-minute compliance assessment. Answer a few questions about your business and get a prioritized list of what OSHA expects, free.

Start free assessment