Skip to main content
Electrical SafetyReviewed against current OSHA standards

Dark by Four O'Clock: What OSHA 1926.405(a)(2) Requires of the Temporary Lights on Your Jobsite

29 CFR 1926.405(a)(2) sets the rules for temporary jobsite lighting: guarded lamps, no hanging by the cord, hard-usage cords and wet-location limits on site.

Updated November 17, 2026
7 min read
By the WorkSafely safety team

In November the light goes before the work does. A remodel crew that used to finish by daylight is now framing the back bedroom with the windows already black, so somebody runs a string of temporary lights down the hallway, hooks it over a few nails, and plugs a work light into the end of it for the basement. A week later the string has a cracked lamp nobody replaced, a section draped across a doorway where the drywall cart rolls over it, and a halogen stand light sitting in the puddle by the sump. None of that is exotic. It is what happens when temporary lighting goes up in a hurry and nobody owns it afterward.

This post answers one question: what does 29 CFR 1926.405(a)(2), the construction standard for temporary wiring, actually require of the lights and cords a small crew strings up when the days get short? It does not cover ground-fault protection for the receptacles those lights plug into. That is 1926.404(b)(1), and we cover the assured equipment grounding option in our post on AEGCP programs under 1926.404. Here the question is the lighting itself.

Temporary wiring is a category, and it has an end date

Section 1926.405(a)(2) is the part of Subpart K that deals with temporary electrical power and lighting installations. The first thing it says is about time. Under 1926.405(a)(2)(i), temporary wiring may be of a class less than would be required for a permanent installation, but it shall be removed immediately upon completion of construction or the purpose for which the wiring was installed. Unless (a)(2) specifically modifies them, the rest of the permanent-wiring requirements in the subpart still apply.

That sentence does two jobs for a small contractor. It gives you permission to use lighter-duty methods, such as cord-and-plug lighting strings instead of conduit and fixed fixtures, while the building is being built. And it puts a limit on that permission. A string of temporary lights that was hung for the rough-in and is still powering the finished basement for the homeowner three months later has stopped being temporary wiring in any useful sense. The practical rule on a small job is simple: the temporary lighting comes down when the work it was hung for is done, and somebody on the crew is responsible for that happening.

Guard the lamp, ground the socket

The paragraph that speaks most directly to lighting is 1926.405(a)(2)(ii)(E). It is two sentences long: all lamps for general illumination shall be protected from accidental contact or breakage, and metal-case sockets shall be grounded. The standard does not prescribe one way to provide that protection, which leaves the employer to choose a method that actually works where the light is hung.

On most jobsites that method is the cage. The plastic or wire guard that comes on a manufactured lighting string is not decoration, and it is often the first thing to go missing when a lamp is changed. A bare bulb at shoulder height in a narrow hallway gets hit by a ladder, a length of pipe or somebody's head, and a broken lamp leaves an exposed energized filament and sharp glass where people are working in poor light. If the guard is gone, the honest options are to replace it or to take that string out of service until it is replaced. Hanging the lamp higher can reduce the chance of contact, but be realistic about the day: a lamp that was out of reach when it was hung is not out of reach once a crew sets up a baker scaffold or a stepladder beneath it.

Portable handlamps, the caged work light on a cord that gets carried from room to room, have their own paragraph. Under 1926.405(j)(1)(iii), metal shell, paper-lined lampholders shall not be used, and handlamps must be equipped with a handle of molded composition or other insulating material and with a substantial guard attached to the lampholder or handle. A handlamp with a cracked handle or a missing cage is out of service.

Not by the cord, and not across the floor

Two more paragraphs cover how temporary lights are hung and how their cords are run. Under 1926.405(a)(2)(ii)(F), temporary lights shall not be suspended by their electric cords unless the cords and lights are designed for that means of suspension. A cord is made to carry current, not weight. Looping it over a nail, wrapping it around a joist or tying it to a pipe puts strain on the jacket and the connections that the cord was never built to take, and the damage tends to happen where nobody can see it. Manufactured strings that are listed for suspension come with their own hangers or hooks; use those, or hang the lights from something built to hold them.

Then there is the path the cord takes. Section 1926.405(a)(2)(ii)(I) requires that flexible cords and cables be protected from damage, that sharp corners and projections be avoided, and that where cords pass through doorways or other pinch points, protection be provided to avoid damage. Doorways are the obvious trouble spot on a remodel, because doors get closed on cords and carts get rolled over them. A cord protector, a ramp, or simply routing the cord overhead through the opening solves most of it. What does not solve it is a cord lying across a threshold that everyone steps over carefully until the day someone does not.

For branch circuits that use open conductors rather than cords, 1926.405(a)(2)(ii)(B) adds specific limits, including that conductors be fastened at intervals not exceeding ten feet and that they not be laid on the floor. Few small crews run open-conductor lighting circuits anymore, but the principle of keeping temporary wiring off the floor carries over to every method.

The cord rating and the plastic housing are part of the rule

Under 1926.405(a)(2)(ii)(J), extension cords used with portable electric tools and appliances must be of three-wire type and designed for hard or extra-hard usage, and flexible cords used with temporary and portable lights must be designed for hard or extra-hard usage as well. That is a specific requirement, and it is checkable: the cord's jacket is printed with its type designation, and the hard-usage and extra-hard-usage types are identified by those markings. A light-duty household extension cord feeding a lighting string does not meet it, however new it looks.

OSHA has addressed lighting strings specifically in a 1981 letter of interpretation on temporary lighting strings used on construction sites. The letter notes that construction sites change continually, and that a lighting string has to keep posing no hazard as conditions change around it. That is the right way to think about this whole section. Temporary lighting is not inspected once on the day it goes up. It is inspected as part of the walk the competent person is already making, which we describe in our post on frequent and regular jobsite inspections under 1926.20.

Splices are the other place cords fail. Under 1926.405(g)(2)(iii), flexible cords shall be used only in continuous lengths without splice or tap, with a narrow exception for hard-service cords No. 12 or larger that are spliced in a way that keeps the insulation, outer sheath properties and usage characteristics of the original cord. Electrical tape wrapped around a cut jacket is not that repair. Under 1926.405(g)(2)(iv), cords also have to be connected to devices and fittings so that strain relief keeps a pull on the cord from being transmitted directly to joints or terminal screws, which is one more reason not to hang a light by its plug.

Wet locations and the sump light

Short days and wet weather arrive together, and the basement light sitting near the sump pit is the one most likely to hurt somebody. Section 1926.405(a)(2)(ii)(G) requires that portable electric lighting used in wet and/or other conductive locations, such as drums, tanks and vessels, be operated at 12 volts or less. It then allows 120-volt lights in those locations if they are protected by a ground-fault circuit interrupter.

For a small crew, that turns into a decision before the light goes down the stairs: either the light is a low-voltage unit, or it is plugged into GFCI protection that you know is working. Either way, the stand light does not sit in standing water, and the cord does not run through it.

Two other requirements in the same paragraph are easy to miss. Under 1926.405(a)(2)(ii)(C), receptacles on temporary circuits must be of the grounding type, and branch circuits used for lighting may not supply receptacles for other purposes. Under (a)(2)(ii)(D), disconnecting switches or plug connectors must be installed so that every ungrounded conductor of each temporary circuit can be disconnected. In plain terms, the lighting circuit is not also the circuit for the tile saw, and there is a clear way to kill each temporary circuit without hunting for it.

A short routine that covers most of it

You do not need a lighting program on paper to get this right, but you do need a routine. When a string goes up, check that every lamp has its guard or is genuinely out of reach, that the string is hung from hangers or supports and not by its cord, and that the cord jacket is marked for hard or extra-hard usage. Route cords overhead or protect them where they cross doorways and traffic. Decide in advance which lights go into wet areas and how they are protected. On each walkthrough, look for missing guards, cracked lamps, taped cords and cords on the floor, and take damaged sections out of service rather than working around them. When the phase of work is finished, take the temporary lighting down.

One note on the broader picture. Separate from the wiring rules, 1926.56 sets minimum illumination levels for construction areas while work is in progress, and in July 2025 OSHA published a proposal to change those illumination requirements. Check the current text on osha.gov before relying on any particular figure. The wiring requirements in 1926.405(a)(2) are a different standard and apply to whatever lights you bring onto the site.

None of this makes a jobsite compliant on its own, and the electrical standards in Subpart K have more to say than one post can cover. But most temporary lighting problems on small jobs come from the same few shortcuts: a missing guard, a cord used as a rope, a light-duty cord borrowed from the garage, and a string nobody took down. Name the person who owns the lights, and check them on the walk you are already doing.

Related reading: Assured Equipment Grounding Under 1926.404 | Portable Generators and Temporary Power | Temporary Heaters on Winter Jobsites

OSHA standards cited

Always verify current OSHA standards at osha.gov. This article reflects standards in effect at the date of publication.

Not sure where you stand?

Take the 5-minute compliance assessment. Answer a few questions about your business and get a prioritized list of what OSHA expects, free.

Start free assessment