The Torch Hose You Never Inspected: What OSHA 1926.350 Asks Before Each Gas Cutting Shift
OSHA 1926.350 covers gas welding and cutting on construction sites: cylinder storage, valve handling, and hose inspection each shift. A practical walk-through.
A two-person crew is cutting rebar and bracket stock on a job site. The oxy-fuel rig lives on a hand cart in the back of the truck, and it has been in and out of that truck for three years. The hoses have been dragged over concrete, run under tailgates, and coiled wet. Nobody on the crew could tell you the last time anyone looked at them closely, because the torch lights and the cut gets made. This post is about the specific things OSHA's construction standard for gas welding and cutting, 29 CFR 1926.350, asks you to do before and during that work, with most of the attention on the parts that crews skip: the hose, the cylinder valve, and where the cylinders sit.
If your question is broader, such as how cylinders should be stored in a shop in general, our posts on compressed gas cylinder safety and welding, cutting and brazing in small shops cover that ground. This one is narrower. It is about the construction-side standard and the routine habits it expects.
Which Standard Applies, and Why It Matters
OSHA splits its rules by industry. General industry operations, like a fabrication shop with a fixed welding bay, fall under Part 1910. Construction work falls under Part 1926, and 1926.350 is titled "Gas welding and cutting." If your crew is cutting steel at a customer's building under construction or renovation, this is the section an inspector reads. Contractors who do both kinds of work, shop fabrication during the week and site installation on a Friday, are often surprised that the same torch kit sits under two different standards depending on where it is being used.
You do not need to memorize the split. You do need to know that the construction standard has specific, observable requirements, and that they are written for exactly the conditions a small crew works in: equipment that travels, a work area that changes daily, and no permanent welding bay with a dedicated cylinder cage.
Cylinders: Caps, Upright, and Separated
Paragraph (a) of 1926.350 covers transporting, moving, and storing compressed gas cylinders. Several of its requirements are plain enough to check in a minute. Valve protection caps must be in place and secured when cylinders are moved. Cylinders must be secured in an upright position at all times, with a brief exception only for the moments when a cylinder is actually being hoisted or carried. And when cylinders are hoisted, they must be secured on a cradle, slingboard, or pallet. The standard specifically rules out magnets and choker slings for that purpose, which matters on a site where someone will eventually be tempted to hook a cylinder onto a crane line to get it up a floor.
The separation rule is the one most often missed on small jobs. Stored oxygen cylinders must be kept apart from fuel gas cylinders or combustible materials by one of two methods. The first is distance: a minimum of 20 feet. The second is a noncombustible barrier at least 5 feet high with a fire-resistance rating of at least one-half hour. On a cramped job site, a crew that parks the oxygen and acetylene cylinders side by side on the same cart overnight, or leaves them leaning against each other in a corner of the building, has not met either option. The reason is not mysterious. Oxygen makes ordinary materials burn far more fiercely, and a fuel gas leak next to an oxygen supply is the combination you are trying to keep apart.
Paragraph (b) adds placement rules for cylinders in use. They should be kept far enough from the actual welding or cutting that sparks, slag, and heat do not reach them, and where that is impractical, fire-resistant shields are required. Cylinders must be placed where they cannot become part of an electrical circuit, which is a real concern on a site where an arc welder and a gas cutting rig are working near each other. And fuel gas cylinders must be placed with the valve end up whenever they are in use.
The Valve Routine That Takes Ten Seconds
Paragraph (d) governs how fuel gas is actually used, and it reads like a short procedure. Before a regulator is connected to a cylinder valve, the valve is to be opened slightly and closed immediately, with the person standing to one side of the outlet. This clears dirt from the valve opening and keeps the operator out of the line of any gas release. When the cylinder is in service, valves on fuel gas cylinders are not to be opened more than one and a half turns, so that the valve can be closed quickly in an emergency. If a special wrench is needed to operate the valve, it is to be left in position on the valve stem while the cylinder is in use, which means anyone can shut the gas off without hunting for a tool. And before a regulator is removed, the cylinder valve is to be closed.
Each of these is the kind of step that experienced operators perform without thinking, and that new hires and borrowed helpers do not know to perform at all. That is the argument for putting them in writing for your crew. A short laminated card in the cart's lid that lists these four steps is cheap, and it turns individual habit into a shared practice.
The same paragraph deals with a failure that should end the job rather than be worked around. If a leak develops at a fuse plug or other safety device on a cylinder, the standard says the cylinder is to be removed from the work area. It is not a repair to attempt with a wrench and tape on the job site.
The Hose: Inspected at the Start of Every Shift
Paragraph (f) is the part of the standard that the opening scene is about. It requires that fuel gas hose and oxygen hose be easily distinguishable from each other and that the two not be interchangeable. It requires that hose couplings be of a type that cannot be unlocked or disconnected by a straight pull without rotary motion, so a snagged hose does not simply pull apart. And it requires that hose in use be inspected at the beginning of each working shift, with defective hose removed from service.
That last requirement is worth pausing on, because it is a daily act, not an annual one. "At the beginning of each working shift" means the person lighting the torch on Tuesday morning has to look at the hose, even though someone looked at it on Monday. What are you looking for? The standard does not give a list of defects here, so use judgment grounded in the obvious: cracks, cuts, burns, soft or swollen spots, worn areas where the hose has been dragged, and fittings that are loose or damaged. Defective hose comes out of service. It is not taped and returned to the cart.
The standard also addresses the aftermath of a flashback. Hose that has been subject to flashback must be tested to twice its normal pressure, and never less than 300 p.s.i., and hose in doubtful condition may not be used. For a small crew, the practical reading is that a flashback event is a reason to stop and treat the hose as suspect, not to relight and keep working. If your crew has no way to run that test, replacing the hose is the cleaner answer.
Paragraph (h) closes the loop on the regulators and gauges, which must be in proper working order while in use. A gauge that no longer reads, or a regulator that creeps, is a defect in the same sense as a cracked hose.
Turning It Into a Habit Your Crew Will Actually Keep
None of this requires a safety department. It requires that someone on the crew owns the rig, and that the start-of-shift look at the hose, the valve routine, and the overnight storage of the cylinders are things the foreman actually asks about. A few small steps help. Put the cylinder separation rule on the truck-loading checklist, so the cart does not ride with oxygen and acetylene touching. Make the hose check part of the same moment as lighting the torch, so it is never a separate task that gets skipped when the schedule is tight. And write down, even informally, who inspected the rig and when, so that if a question is ever raised, you can show a practice rather than a memory.
This post describes what the standard says; it is not a substitute for reading 1926.350 in full or for the judgment of someone qualified to look at your equipment. Following these habits does not by itself make a job compliant, but a crew that does them consistently has removed most of the easy ways for a gas cutting rig to hurt someone.
Related reading: Compressed Gas Cylinders: The Hazard Hiding in Plain Sight | Welding, Cutting, and Brazing Safety for Small Shops
OSHA standards cited
- 29 CFR 1926.350
Construction Industry Standards
- 29 CFR Part 1910
General Industry Standards
Always verify current OSHA standards at osha.gov. This article reflects standards in effect at the date of publication.
Not sure where you stand?
Take the 5-minute compliance assessment. Answer a few questions about your business and get a prioritized list of what OSHA expects, free.
Related Articles
Continue learning about OSHA compliance and workplace safety
Construction Safety
The Saw on the Tailgate: What OSHA 1926.304 Requires of the Circular Saws and Table Saws Your Crew Brings to the Job
29 CFR 1926.304 sets guard rules for jobsite woodworking tools: lower guards on circular saws, hoods on table saws, and lockable switches on fixed tools.
Construction Safety
Temporary Heaters on Winter Jobsites: What 29 CFR 1926.154 Requires for Clearance, Ventilation and Fuel
29 CFR 1926.154 sets the rules for jobsite heaters: fresh air, clearance from combustibles and tarps, level setup and fuel controls. A guide for small crews.
Construction Safety
The Tenant Is Still Working Upstairs: What OSHA 1926.34 Requires of Your Crew's Exits
OSHA 1926.34 requires free, unobstructed, marked exits in any occupied building. See what that means when your crew works inside a space people still use.