The Saw on the Tailgate: What OSHA 1926.304 Requires of the Circular Saws and Table Saws Your Crew Brings to the Job
29 CFR 1926.304 sets guard rules for jobsite woodworking tools: lower guards on circular saws, hoods on table saws, and lockable switches on fixed tools.
This post answers one question: what does OSHA's construction standard for woodworking tools, 29 CFR 1926.304, actually require of the saws a small crew cuts with on site? If you run a shop with fixed woodworking machines, the general industry rule is different, and our post on what 1910.213 requires before you turn on the saw covers it. This one is about the framing crew, the trim carpenter and the remodeler, and the saws that ride to the job in the truck.
Picture a normal morning on a small renovation. A portable table saw is set up on a stand in the garage, its blade guard sitting on a windowsill because it got in the way of a narrow rip yesterday. The lead carpenter's circular saw has a lower guard that sticks halfway, so he has been flicking it back with a thumb. A miter saw is plugged into a cord that runs across the driveway. None of this feels unusual. All of it is exactly what 1926.304 was written about.
What 1926.304 covers, and what it leaves to other rules
Section 1926.304 sits in Subpart I of the construction standards, the subpart on hand and power tools. It is short. It has nine paragraphs, lettered (a) through (i), and most of them are a sentence or two. That brevity is easy to misread as leniency. In practice it means the few things the rule does say are specific, and an inspector can check each of them by looking at the tool.
The section does not stand alone. Subpart I opens with 1926.300, which applies to every hand and power tool on the job. Under 1926.300(a), all hand and power tools, "whether furnished by the employer or the employee," must be maintained in a safe condition. That phrase matters on small crews, where the saw is often the carpenter's own. Under 1926.300(b)(1), when a power tool is designed to accommodate guards, it must be equipped with those guards when in use. So a saw that came from the factory with a guard is expected to have that guard on it while it cuts. The woodworking section then adds the specifics for saws and other woodworking tools.
Paragraph (e) of 1926.304 ties the section to personal protective equipment: any PPE provided must meet Subpart E. For saw work that usually means eye protection under 1926.102, and depending on the noise, hearing protection under 1926.101. Paragraph (f) adds that woodworking tools and machinery must meet other applicable requirements of the American National Standards Institute safety code for woodworking machinery, ANSI O1.1-1961. That is an old consensus code, and the rule incorporates it by reference, so the federal text is not the whole story for unusual machines.
The portable circular saw: two guards, and the lower one has to come back on its own
Paragraph (d) is the one most small contractors will meet every day. It requires that all portable, power-driven circular saws be equipped with guards above and below the base plate or shoe. The upper guard must cover the saw to the depth of the teeth, except for the minimum arc needed to tilt the blade for bevel cuts. The lower guard must cover the saw to the depth of the teeth, except for the minimum arc needed for the guard to retract and contact the work.
Then comes the clause that matters most in the field. When the tool is withdrawn from the work, the lower guard must automatically and instantly return to the covering position. A guard that is present but sticks does not do that. Neither does a guard pinned back with a wedge of wood, a zip tie or electrical tape so it will not catch on the edge of a sheet. A sticky lower guard is usually a cleaning or spring problem: pitch and sawdust packed into the pivot, or a weak return spring. It is rarely something the operator should work around with a thumb.
Paragraph (d) does not tell you how often to check that guard, but 1926.300(a) does put the burden on you to keep the tool in a safe condition, and the simplest way to show that is a short check before the saw goes to work. Lift the guard and let it go. It should snap closed without help. If it hesitates, the saw comes out of service until it is cleaned or repaired. Our hand and power tool inspection checklist covers guards, cords and the other points worth recording on saws and portable tools during a periodic inspection, so the condition of the crew's tools gets written down rather than remembered.
Table saws and radial saws on site: the hood rule
The second group of requirements covers the saws people set up on a stand or a bench at the job. Paragraph (h)(1) says each circular hand-fed crosscut table saw must be guarded by a hood that meets the requirements for ripsaw hoods in paragraph (i)(1). Paragraph (i)(1) then describes that hood. It must completely enclose the portion of the saw above the table and above the material being cut. It must automatically adjust to the thickness of the material and remain in contact with it, while offering little resistance to feeding the stock. It has to be strong enough to take reasonable use, protect the operator from flying splinters and broken teeth, and be made of material soft enough that it will not break the saw teeth if they touch it. It must be mounted so it stays in true alignment with the saw.
Most portable jobsite table saws are sold with a guard assembly that is designed to do these things. The common failure is not that the guard is missing from the box; it is that it was taken off for one awkward cut and never went back on. Under 1926.300(b)(1), if the saw is designed for the guard, the guard belongs on the saw when it is in use. If a particular cut genuinely cannot be made with the hood in place, that is a reason to plan the cut differently, use a different tool, or bring the work back to a shop where it can be done properly. It is not a reason to run the saw bare for the rest of the job.
Paragraph (g)(1) covers radial saws, which some crews still run on site for repetitive crosscuts. The upper hood must completely enclose the upper portion of the blade down to a point that includes the end of the saw arbor, protect the operator from flying splinters and broken teeth, and deflect sawdust away from the operator. The sides of the lower exposed portion of the blade must be guarded to the full diameter of the blade by a device that automatically adjusts to the thickness of the stock and stays in contact with it.
Switches, speeds and feeders: the paragraphs that apply to fixed tools
Paragraph (a) applies to fixed power-driven woodworking tools. Each must have a disconnect switch that can be locked or tagged in the off position. On a construction site, "fixed" can include equipment set up for the duration of a job, such as a saw mounted in a temporary cutting station. The point of the switch is simple: whoever changes a blade, clears a jam or adjusts the fence should be able to make sure nobody else starts the machine while their hands are near it.
Paragraph (b) deals with large saws. Circular saws over 20 inches in diameter, or operated at over 10,000 peripheral feet per minute, must have their operating speed etched or otherwise permanently marked on the blade, and must not be run at any other speed. If the saw is retensioned for a different speed, the marking must be corrected. Most small crews never touch a blade that size, but if you rent a large saw for a specific job, check that the marking is there.
Paragraph (c) says automatic feeding devices should be installed on machines whenever the nature of the work permits, and that feeder attachments must have their feed rolls and other moving parts covered or guarded to protect the operator from hazardous points. Again, this is unusual on small jobsites, but it applies when the equipment is there.
Making it work on a small crew
The practical problem with 1926.304 on a small job is not understanding it. Every carpenter knows what a saw guard is for. The problem is that guards come off for good reasons and stay off for bad ones, and nobody is assigned to notice. A few habits close most of that gap.
Decide who owns each stationary saw on a job, and make that person responsible for the hood being on it at the start of each day. Treat a pinned or sticking lower guard on a circular saw as a tool defect, not as an operator preference, and take the saw out of service the same way you would a cord with exposed conductors. Because 1926.300(a) reaches tools "furnished by the employee," include personal saws in the same check rather than looking only at the company's tools. Keep the disconnect or plug within reach when blades are changed, and make unplugging the saw part of the blade change rather than an afterthought. And when you look over the job during the regular inspections 1926.20(b)(2) expects a competent person to make, include the cutting station on the walk.
None of this makes a jobsite compliant on its own, and Subpart I has more to say than one post can cover. But most saw guarding problems on small jobs come down to the same two shortcuts: a lower guard that is held back, and a table saw hood sitting somewhere other than on the saw. Fix those two, and you have addressed what this section is mostly about.
Related reading: Woodworking Machinery Safety Under 1910.213 | Hand and Power Tool Safety | Construction Noise and Hearing Protection Under 1926.52
OSHA standards cited
- 29 CFR 1926.304
Construction Industry Standards
- 29 CFR 1910.213
General Industry Standards
- 29 CFR 1926.300
Construction Industry Standards
- 29 CFR 1926.102
Construction Industry Standards
- 29 CFR 1926.101
Construction Industry Standards
- 29 CFR 1926.20
Construction Industry Standards
- 29 CFR 1926.52
Construction Industry Standards
Always verify current OSHA standards at osha.gov. This article reflects standards in effect at the date of publication.
Not sure where you stand?
Take the 5-minute compliance assessment. Answer a few questions about your business and get a prioritized list of what OSHA expects, free.
Related Articles
Continue learning about OSHA compliance and workplace safety
Construction Safety
Temporary Heaters on Winter Jobsites: What 29 CFR 1926.154 Requires for Clearance, Ventilation and Fuel
29 CFR 1926.154 sets the rules for jobsite heaters: fresh air, clearance from combustibles and tarps, level setup and fuel controls. A guide for small crews.
Construction Safety
The Tenant Is Still Working Upstairs: What OSHA 1926.34 Requires of Your Crew's Exits
OSHA 1926.34 requires free, unobstructed, marked exits in any occupied building. See what that means when your crew works inside a space people still use.
Construction Safety
Who Decides the Concrete Is Ready? Stripping Forms and Shores Under OSHA 1926.703
OSHA 1926.703 bars removing forms and shores until the employer determines the concrete is strong enough. See what that rests on and when shoring is inspected.