Skip to main content
Construction SafetyReviewed against current OSHA standards

Temporary Stairways on a Small Job Site: What OSHA 1926.1052 Requires Before Anyone Carries Material Up Them

OSHA 1926.1052 sets rules for temporary stairways, stair rails and handrails on construction sites. Here is what a small contractor has to have in place.

Updated October 13, 2026
6 min read
By the WorkSafely safety team

On a two-story renovation or a small commercial build, the first way up to the second floor is rarely a finished staircase. It is a ladder leaned against a slab edge, a set of site-built wooden steps, or a metal pan stair that arrived before the concrete did. Everyone uses it, many times a day, usually carrying something. Because it is "just for now," it tends to get less attention than almost anything else on the job, and it is the route on which a trip with a bundle of drywall in both arms turns into a fall of ten feet.

This post answers one narrow question: when a stairway is going to be used during construction but will not be part of the finished structure, or is part of the structure but not yet finished, what does OSHA's construction stairway standard in 29 CFR 1926.1052 expect you to have in place? It does not cover portable ladders, which are handled in 1926.1053, or the fall protection rules for open edges and holes in 1926.501.

When you need a stairway at all

The starting point is actually the general requirements section, 1926.1051. It says a stairway or ladder must be provided at every personnel point of access where there is a break in elevation of 19 inches or more and no ramp, runway, sloped embankment, or personnel hoist is provided. Nineteen inches is not very much. A footing trench, a raised slab, a loading platform, and a mezzanine all qualify. If people have to climb it to get to work, the standard expects something deliberate there, not a stack of pallets or a convenient scaffold frame.

The same section also says the employer must install the stairway and ladder fall protection systems the subpart requires before employees begin the work that needs them. In practice that means the stair rail goes up with the stairs, not "when we get to it." A stairway that is in use without the rail it is supposed to have is a violation whether or not anyone has fallen.

Geometry: the part that causes trips

Much of 1926.1052 is about making a stairway behave predictably under a tired, loaded foot. For stairs that will not be a permanent part of the structure, the standard calls for landings at least 30 inches deep in the direction of travel and at least 22 inches wide at every 12 feet or less of vertical rise. A single long flight with no place to stop is something the standard is designed to prevent.

Stairs are to be installed at an angle between 30 and 50 degrees from horizontal. Anything steeper is a ladder in practice and should be treated as one, with the ladder rules applying. Anything much shallower is easy to build but takes up floor area that small sites often do not have, which is one reason crews are tempted to cheat the angle.

Uniformity matters even more than the particular dimensions. Riser height and tread depth have to be uniform within a flight of stairs, and that includes any foundation or structure used as one of the steps. The standard allows variation of no more than one quarter inch in any stairway system. The classic failure here is the site-built stair that is accurate everywhere except the first step, where it meets whatever the ground happens to be doing. A muddy, uneven bottom step that is two inches taller than the rest is exactly the sort of thing a person's foot does not expect, and it does not matter that the other fourteen risers were cut perfectly.

Where a door or gate opens directly onto a stairway, a platform is required, and the swing of the door must not reduce the effective width of that platform below 20 inches. This comes up when a door to a stairwell is hung before the permanent stair is finished. The opening swings out over the first tread, and the person who pushes it open steps into space.

Pan stairs that have not been filled yet

Permanent steel pan stairs are an everyday source of confusion. They are delivered and set early, and the concrete or other fill for the treads and landings is poured later. In the meantime, the open metal pans look like a staircase and feel like one, and workers will use them.

Section 1926.1052(b) addresses this directly. Except during construction of the stairway itself, foot traffic is prohibited on pan stairs whose treads or landings are to be filled later, unless the stairs are temporarily fitted with wood or another solid material, at least to the top edge of each pan. The standard also says those temporary treads and landings should be replaced when they wear down below the top edge of the pan. In other words, a pan stair with empty pans is not available for use, and a pan stair with plywood in it needs to be looked at again as the plywood wears.

For a small contractor, the practical lesson is to decide before the stairs arrive who is responsible for filling the pans with temporary material, and to make that part of the delivery, not an afterthought for the first person who needs to go upstairs.

Handrails and stair rails: what they are and when they are needed

The standard uses two terms that are easy to blur. A handrail is something you grip while you climb. A stair rail is a barrier along the open side of the stairs that stops a person from falling off them. They do different jobs, and a stairway may need both.

Under 1926.1052(c), stairways with four or more risers, or that rise more than 30 inches, whichever is less, need at least one handrail and a stair rail along each unprotected side or edge. That threshold is low enough that a short set of steps up to a temporary platform is usually covered.

The standard also gives dimensions. A stair rail installed after March 15, 1991 has to be not less than 36 inches from its upper surface to the surface of the tread, measured in line with the face of the riser at the forward edge of the tread. A handrail has to be not more than 37 inches nor less than 30 inches from its upper surface to the tread surface. Handrails and the top rails of stair rail systems must be able to withstand a force of at least 200 pounds applied within two inches of the top edge in any downward or outward direction, at any point along the rail, without failing.

That last requirement is the one that separates a real rail from a decoration. A two-by-four nailed at the right height across a few posts with finish nails is easy to put up and easy to fail a push test. A rail that comes loose when someone leans on it, or when a person trips and grabs it, is worse than no rail at all because it creates confidence the structure has not earned.

Making inspection part of the routine

The standard does not tell you how often to inspect a temporary stair. It does expect it to remain in the condition the rest of the rules describe, and temporary things degrade quickly on a working site. Treads get covered with mud, drywall dust, or ice. Rails get knocked loose when materials are carried past. Plywood fill wears through. Someone removes a handrail bracket to move a pallet and does not put it back.

For a small crew, the workable habit is to treat the stair like any other piece of equipment that people depend on: a quick look by the competent person or foreman at the start of each shift, with a short list of what to check. Are the treads clear and solid? Are the risers the same height, especially at the bottom? Is the rail present on every open side, at height, and does it hold when pushed? Are any pans empty? Is there a landing where the climb is long? Anything that fails is fixed or the stair is closed before work continues, and the closure is communicated, not assumed.

What this does not do for you

Following the stairway rules does not by itself make a job site compliant. Open edges at the top of a stair, holes in the floor next to it, and ladders used as alternate access each fall under other parts of the construction standards. Whether a particular stair meets the standard on your site also depends on details of the structure and the work being done, and a state plan may add requirements of its own. Treat 1926.1052 as the floor for the stair itself, not the whole picture of access safety on the job.

The goal is simple to state. The way up should be the safest part of the building, not the least considered. If it is built to the standard, kept clean, and checked each morning, it usually is.

Related reading: Who Is Allowed to Fire a Powder-Actuated Tool? What OSHA 1926.302(e) Requires Before Anyone Pulls the Trigger | Demolition Safety for Small Contractors: What OSHA 1926.850 Actually Requires | Crane Operator Certification: What OSHA 1926.1427 Actually Requires of Small Contractors

OSHA standards cited

Always verify current OSHA standards at osha.gov. This article reflects standards in effect at the date of publication.

Not sure where you stand?

Take the 5-minute compliance assessment. Answer a few questions about your business and get a prioritized list of what OSHA expects, free.

Start free assessment